1. Introduction
This manual provides essential information for the safe and efficient operation of your lightmaXX Nano Beam FX show effect light. Please read it thoroughly before use and retain it for future reference.
2. Safety Instructions
- Read all instructions carefully.
- Keep this manual for future reference.
- Do not expose the device to rain or moisture.
- Ensure proper ventilation.
- Disconnect from power before cleaning or servicing.
- Use only specified power supply.
- Avoid direct eye exposure to the light source.
- This device is for indoor use only.
- Ensure the mounting bracket is securely fastened.
3. Package Contents
Verify that all items are present and in good condition.
- lightmaXX Nano Beam FX Unit
- Power Cable
- Remote Control
- Instruction Manual (this document)
Image 1: lightmaXX Nano Beam FX unit, power cable, and remote control.
4. Product Overview
4.1 Front Panel
The front panel features multiple lenses for projecting various light effects.
Image 2: Close-up view of the front lenses.
4.2 Rear Panel and Connections
The rear panel provides power input/output, DMX connections, and control interface.
Image 3: Rear panel with connections and control interface.
- POWER IN: Connect the supplied power cable here.
- POWER OUT: For daisy-chaining power to other units.
- DMX IN: Connect DMX controller or previous DMX device.
- DMX OUT: Connect to the next DMX device in the chain.
- MIC: Built-in microphone for sound-activated modes.
- Display & Buttons: For menu navigation and settings (MENU, UP, DOWN, ENTER).
- SAFETY ROPE: Attachment point for a safety cable.
4.3 Remote Control
The included remote control allows for convenient operation of the unit's functions.
Image 4: Remote control for the Nano Beam FX.
- ON/OFF: Power on or off the unit.
- AUTO: Activates automatic program mode.
- MUSIC 1/2/3: Activates sound-activated modes with different sensitivities or patterns.
- STROBE: Activates strobe effect.
- PRO LIGHT: Adjusts light intensity or program selection.
- SPEED/SEN: Adjusts program speed or sound sensitivity.
5. Setup
5.1 Unpacking
Carefully remove the unit from its packaging. Inspect for any damage during transit. Retain packaging for future transport or storage.
5.2 Mounting
The Nano Beam FX unit is equipped with a mounting bracket for secure installation.
Image 5: Adjustable mounting bracket.
- Attach the unit securely to a truss, ceiling, or wall using appropriate clamps and hardware (not included).
- Always use a safety cable (not included) attached to the SAFETY ROPE point on the rear panel, ensuring it can hold the weight of the unit.
- Adjust the angle of the unit using the knobs on the mounting bracket.
5.3 Power Connection
Connect the supplied power cable to the POWER IN socket on the rear panel and then to a suitable power outlet.
5.4 DMX Connection (Optional)
For advanced control, connect the unit to a DMX controller.
- Connect a DMX cable from your DMX controller's output to the DMX IN socket of the Nano Beam FX.
- If connecting multiple DMX devices, connect from the DMX OUT of the first unit to the DMX IN of the next.
- Refer to the DMX channel chart (not provided in product data) for specific DMX control parameters.
6. Operating
6.1 Power On/Off
Press the ON/OFF button on the remote control or ensure the unit is connected to power. The unit will power on automatically when connected to power.
6.2 Operating Modes
The Nano Beam FX offers several operating modes, selectable via the remote control or the rear panel display.
- AUTO Mode: Press the AUTO button on the remote. The unit will cycle through its pre-programmed light shows automatically.
- MUSIC Mode: Press MUSIC 1, MUSIC 2, or MUSIC 3 on the remote. The unit will react to sound picked up by its internal microphone. Different music modes may offer varying sensitivities or patterns.
- STROBE Mode: Press the STROBE button on the remote to activate a flashing light effect.
- DMX Mode: If connected to a DMX controller, the unit will respond to DMX signals. Use the rear panel display to set the DMX address.
Image 6: Example of light effects (blue and red).
Image 7: Example of light effects (green and yellow).
Image 8: Example of light effects (orange and red).
6.3 Adjustments via Remote Control
- PRO LIGHT: Use the + and - buttons to cycle through different light programs or adjust intensity in certain modes.
- SPEED/SEN: Use the + and - buttons to adjust the speed of automatic programs or the sensitivity of sound-activated modes.
7. Maintenance
7.1 Cleaning
Disconnect the unit from power before cleaning. Use a soft, lint-free cloth to wipe the exterior. For lenses, use a specialized lens cleaner and cloth to avoid scratches. Do not use abrasive cleaners.
7.2 Storage
When not in use, store the unit in its original packaging or a suitable case in a dry, dust-free environment.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on. | No power supply; faulty cable. | Check power cable connection; try a different outlet. |
| Remote control not working. | Dead battery; obstruction; out of range. | Replace remote battery; ensure clear line of sight; move closer to unit. |
| No light effects. | Unit in DMX mode without DMX signal; program not selected. | Select AUTO or MUSIC mode; check DMX connection and settings. |
| Sound-activated mode not responding. | Microphone sensitivity too low; no sound input. | Increase sensitivity using remote; ensure sound source is close to the unit. |
9. Specifications
| Feature | Detail |
|---|---|
| Model | Nano Beam FX |
| Brand | lightmaXX |
| Product Dimensions | 32 x 30 x 29 cm |
| Item Weight | 3.5 kg |
| Power Source | Corded Electric |
| Light Source Wattage | 3 Watts (per light source) |
| Number of Light Sources | 24 |
| Manufacturer Reference | LIG0015648-000 |
| ASIN | B07JM9XVT4 |
10. Warranty and Support
For warranty information and technical support, please refer to the manufacturer's official website or contact your retailer. Keep your proof of purchase for any warranty claims.