LS2 Helmets Valiant FF399 Replacement Face Shield User Manual

1. Introduction

This user manual provides essential information for the proper installation, use, and maintenance of your LS2 Helmets Valiant FF399 Replacement Face Shield. Please read this manual thoroughly before installation and use to ensure safety and optimal performance.

The LS2 Valiant FF399 Replacement Face Shield is designed specifically for LS2 Valiant helmets (model FF399). This particular shield is a dark smoke tint, made from PC material with anti-scratch properties. It is important to note that dark smoke visors are not safe for night riding due to reduced visibility.

Image: LS2 Valiant FF399 Dark Smoke Replacement Face Shield. This image shows the dark smoke tinted visor, designed for replacement on LS2 Valiant FF399 helmets. It has a curved shape to fit the helmet's contours and features mounting points on the sides.

2. Setup and Installation

The LS2 Valiant FF399 Replacement Face Shield is designed for easy installation. Follow these general steps for replacing your helmet's visor. Refer to your LS2 Valiant helmet's original manual for specific instructions if available.

1. Preparation: Ensure your helmet is clean and free of debris around the visor mechanism.
2. Removing the Old Visor:
   • Locate the visor release mechanisms on both sides of your LS2 Valiant FF399 helmet. These are typically levers or buttons near the pivot points.
   • Engage the release mechanism on one side, then gently pull the visor away from the helmet to disengage it from the pivot.
   • Repeat for the other side. Carefully remove the old visor.
3. Installing the New Visor:
   • Align the pivot points of the new LS2 Valiant FF399 Replacement Face Shield with the corresponding slots on the helmet's mechanism.
   • Gently push the visor into place until you hear or feel a click, indicating it is securely engaged.
   • Repeat for the other side.
4. Verification: Once installed, gently move the visor up and down several times to ensure it operates smoothly and locks securely in both the open and closed positions. Check that both sides are evenly seated.

Important Safety Note:

Ensure the visor is correctly installed and securely latched before riding. A loose or improperly installed visor can detach during operation, leading to serious injury.

3. Operating Guidelines

This replacement face shield is designed for use with LS2 Valiant FF399 helmets. Adhere to the following guidelines for safe and effective operation:

• Daytime Use Only: The dark smoke tint of this visor significantly reduces light transmission. It is not safe for use during night riding, in low-light conditions, or in adverse weather (e.g., heavy rain, fog) where visibility is already compromised. Always use a clear visor for such conditions.
• Visibility: Always ensure your vision is unobstructed. If the visor becomes scratched, damaged, or excessively dirty, replace it immediately to maintain clear visibility.
• Pinlock System: This shield may feature a Pinlock system for anti-fogging. If present, ensure the Pinlock insert (sold separately or included with some helmets) is properly installed according to its instructions to prevent fogging.
• Opening and Closing: Operate the visor smoothly using the designated tab or lip. Avoid forcing the visor, which could damage the mechanism or the shield itself.

4. Maintenance and Care

Proper care will extend the life of your LS2 Valiant FF399 Replacement Face Shield and maintain its optical clarity.

• Cleaning:
  • Use only mild soap and lukewarm water to clean the visor.
  • Gently wipe with a soft, lint-free cloth. Avoid abrasive materials or harsh chemical cleaners, as these can damage the anti-scratch coating and tint.
  • For stubborn dirt or dried insects, place a wet cloth over the affected area for a few minutes to soften the debris before gently wiping.
• Drying: Allow the visor to air dry or gently pat dry with a clean, soft microfiber cloth.
• Storage: When not in use, store the visor in a protective bag or case to prevent scratches. Avoid exposing it to extreme temperatures or direct sunlight for prolonged periods.
• Inspection: Regularly inspect the visor for scratches, cracks, or other damage. Replace the visor if any damage is present that could impair visibility or compromise safety.

5. Troubleshooting

Most issues with a replacement visor are related to installation or cleaning. Here are some common points:

• Visor does not close properly or feels loose:
  • Ensure both sides of the visor are fully engaged with the helmet's pivot mechanisms. Re-install if necessary.
  • Check for any debris or obstructions in the pivot mechanism.
• Excessive fogging:
  • Ensure any Pinlock insert is correctly installed and sealed.
  • Verify that the helmet's ventilation system is open and functioning correctly.
  • Consider using an anti-fog spray designed for helmet visors.
• Scratches or reduced clarity:
  • If the anti-scratch coating is compromised or the visor is heavily scratched, it cannot be repaired. Replacement is necessary for safety.

If you encounter persistent issues not covered here, please contact LS2 customer support or consult a qualified helmet technician.

6. Specifications

7. Warranty and Support

For information regarding warranty coverage, product support, or to purchase additional accessories, please visit the official LS2 Helmets website or contact their customer service department. Keep your purchase receipt as proof of purchase.

LS2 Official Store: Visit the LS2 Store on Amazon