Instruction Manual for HONONJO RM-PJ7 Remote Control
Model: RM-PJ7
Introduction
This manual provides detailed instructions for the HONONJO RM-PJ7 replacement remote control, designed for various Sony Projector models. Please read this manual carefully before using the remote control to ensure proper operation and longevity of the device.
The RM-PJ7 remote control is a high-quality replacement unit that offers full functionality comparable to the original Sony projector remote. It features an ergonomic design for comfortable handling and intuitive button layout for ease of use.
Compatible Projector Models:
- Sony VPL-BW120S
- Sony VPL-CW255
- Sony VPL-CW275
- Sony VPL-CX235
- Sony VPL-CX275
- Sony VPL-EX100
- Sony VPL-EX120
- Sony VPL-EX145
- Sony VPL-EX175
- Sony VPL-SW125
- Sony VPL-SW525
- Sony VPL-SW525C
- Sony VPL-SW535
- Sony VPL-SW535C
- Sony VPL-SW535EBPAC
- Sony VPL-SX125
- Sony VPL-SX535
- Sony VPL-SX535EBPAC
Setup
Battery Installation:
The RM-PJ7 remote control requires two (2) AAA batteries (not included) for operation. Follow these steps to install the batteries:
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards or in the direction indicated by an arrow to open it.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment. Incorrect insertion can prevent the remote from functioning.
- Slide the battery compartment cover back into place until it clicks securely.
Image: Front and back view of the RM-PJ7 remote control. The front displays various function buttons, while the back clearly shows the battery compartment with its cover. This image illustrates where to insert the batteries.
Once batteries are installed, the remote control is ready for use. No programming or pairing is typically required for this infrared (IR) remote control; simply point it at your compatible Sony projector.
Operating Instructions
The RM-PJ7 remote control provides access to various functions of your Sony projector. Below is a guide to the main buttons and their functions:
| Button | Function |
|---|---|
| Power (/) | Turns the projector on or off. |
| INPUT | Cycles through available input sources (e.g., HDMI, VGA, USB). |
| MENU | Opens or closes the projector's on-screen menu. |
| APA | Automatic Pixel Alignment (for analog PC input). Optimizes the image quality. |
| ECO MODE | Toggles the projector's Eco Mode, which reduces lamp brightness and power consumption, extending lamp life. |
| Navigation Arrows (Up, Down, Left, Right) | Navigates through menu options and adjusts settings. |
| ENTER | Confirms selections within the menu or activates a function. |
| RETURN | Goes back to the previous menu screen or exits a sub-menu. |
| RESET | Resets certain projector settings to their default values. Use with caution. |
| ASPECT | Changes the aspect ratio of the projected image (e.g., 4:3, 16:9). |
| KEYSTONE | Adjusts the keystone distortion to correct trapezoidal images. Use the +/- buttons to adjust. |
| D ZOOM (+/-) | Digitally zooms in or out on the projected image. |
| VOLUME (+/-) | Adjusts the audio output volume of the projector. |
| FREEZE | Pauses the current image on the screen. Press again to unfreeze. |
| AUDIO MUTING | Mutes or unmutes the audio output. |
| PIC MUTING | Blanks the projected image (turns off the lamp temporarily) without turning off the projector. Press again to restore the image. |
For detailed information on specific projector functions, please refer to your Sony projector's original user manual.
Maintenance
Cleaning the Remote Control:
To maintain the remote control's appearance and functionality, follow these cleaning guidelines:
- Wipe the surface of the remote control with a soft, dry cloth.
- For stubborn dirt, lightly dampen the cloth with water or a mild, non-abrasive cleaner. Ensure no liquid enters the remote control.
- Do not use harsh chemicals, abrasive cleaners, or solvents as they may damage the remote's finish or internal components.
Battery Replacement:
Replace batteries when the remote control's range decreases significantly or it stops responding. Always replace both batteries at the same time with new AAA batteries. Do not mix old and new batteries, or different types of batteries.
Storage:
If the remote control will not be used for an extended period, remove the batteries to prevent leakage and potential damage to the remote control.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control not working. | Dead or incorrectly installed batteries. | Check battery polarity (+/-). Replace with fresh AAA batteries. |
| Remote control range is poor. | Weak batteries; Obstruction between remote and projector; Remote sensor on projector is dirty or blocked. | Replace batteries. Ensure a clear line of sight to the projector's IR sensor. Clean the projector's IR sensor if necessary. |
| Specific buttons not responding. | Button malfunction; Projector not supporting the function. | Ensure your projector model supports the specific function. If other buttons work, the specific button might be faulty (rare). |
| Projector does not respond to any remote commands. | Projector is off or in standby; Projector's IR sensor is faulty. | Ensure the projector is powered on. Test with another compatible remote if available. Consult projector's manual for IR sensor issues. |
If the problem persists after trying these solutions, please contact the seller or manufacturer for further assistance.
Specifications
| Feature | Detail |
|---|---|
| Brand | HONONJO |
| Model | RM-PJ7 |
| Material | Plastic |
| Working Range | Within 26 Feet (8 Meters) |
| Batteries Required | 2 x AAA (NOT Included) |
| Connectivity Technology | Infrared |
| Controller Type | Button Control |
| Special Feature | Ergonomic |
| Compatible Devices | Projector |
Warranty and Support
This HONONJO remote control is designed for reliable performance. For specific warranty information, please refer to the terms provided by your retailer or the HONONJO manufacturer at the time of purchase. Typically, replacement remote controls come with a limited warranty against manufacturing defects.
If you encounter any issues not covered in the troubleshooting section or require further assistance, please contact the seller from whom you purchased this product. Provide your order details and a clear description of the issue for prompt support.
For general inquiries or to explore other products, you may visit the HONONJO Store on Amazon.
