Introduction
This instruction manual provides essential information for the safe installation, operation, and maintenance of your Knightsbridge Screwless 6G Grid Faceplate, model GDSF006MB. Please read these instructions carefully before installation and retain them for future reference.
Important Safety Information
WARNING: Electrical installations should only be carried out by a qualified electrician in accordance with national wiring regulations. Always isolate the mains power supply before commencing any electrical work.
- Ensure the power supply is disconnected at the consumer unit/fuse board before installation.
- This product is designed for indoor use only.
- Do not install on damp or freshly plastered surfaces.
- Ensure all connections are secure and correctly wired.
- This product is rated IP20, meaning it is protected against solid objects over 12.5mm, but has no protection against water.
Installation Instructions
The Knightsbridge Screwless 6G Grid Faceplate is designed for easy installation over a compatible 6-gang grid module. Follow these steps for a secure and aesthetic finish.
- Prepare the Grid Module: Ensure your 6-gang grid module (not supplied) is correctly installed and wired into the wall box according to electrical regulations. The module should be securely fixed to the wall box.
- Attach the Faceplate Frame: The screwless faceplate consists of two parts: a main frame and a decorative front plate. Align the main frame with the grid module and secure it using the screws provided with your grid module. Ensure it is flush with the wall.
- Secure the Decorative Front Plate: Once the main frame is securely attached, carefully clip the decorative screwless front plate onto the main frame. Apply gentle, even pressure until it clicks into place. Ensure all edges are flush and there are no gaps.
Image 1: Front view of the Knightsbridge Screwless 6G Grid Faceplate. This image shows the six openings for grid modules and the sleek, screwless design.
Image 2: Angled view of the Knightsbridge Screwless 6G Grid Faceplate, highlighting its slim profile and matt black finish.
Operation
The screwless faceplate itself does not have operational functions. Its purpose is to provide a clean, aesthetic finish for your installed 6-gang grid modules (e.g., light switches, dimmer switches, or sockets). Once installed, the functionality is determined by the grid modules fitted within it.
To remove the decorative front plate for maintenance or access to the grid modules, carefully insert a small flat-head screwdriver into the notch at the bottom edge of the faceplate and gently pry it off. Exercise caution to avoid damaging the finish.
Maintenance and Cleaning
To maintain the appearance and functionality of your faceplate, follow these simple guidelines:
- Cleaning: Wipe the surface with a soft, dry cloth. For stubborn marks, a slightly damp cloth with mild soap can be used, followed by drying with a clean, soft cloth.
- Avoid: Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the matt black finish.
- Inspection: Periodically check for any signs of damage or loose connections. If any issues are found, consult a qualified electrician.
Troubleshooting
This section addresses common concerns related to the faceplate itself. For issues related to the electrical functionality of the grid modules, refer to their respective manuals or consult a qualified electrician.
| Problem | Possible Cause | Solution |
|---|---|---|
| Faceplate does not sit flush. | Main frame not properly secured or wall box uneven. | Ensure the main frame is tightly screwed to the wall box. Check if the wall surface is even. |
| Decorative front plate does not clip on. | Misalignment or obstruction. | Re-align the front plate with the main frame. Check for any debris or obstructions preventing it from clicking into place. |
| Scratches or marks on the finish. | Abrasive cleaning or impact. | Avoid abrasive cleaners. Handle with care during installation and cleaning. Minor marks may be permanent. |
Specifications
| Model Number: | GDSF006MB |
| Description: | Screwless 6G Grid Faceplate |
| Finish: | Matt Black |
| Material: | Premium Grade Steel (Alloy Steel) |
| Dimensions (H x W x D): | 148mm x 148mm x 3.5mm |
| Nett Weight: | 0.09 kg (90 grams) |
| IP Rating: | IP20 |
| Manufactured in accordance with: | BS EN 60670-1 |
| Origin of Manufacture: | China |
Warranty
This Knightsbridge product comes with a 15-year warranty from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by improper installation, misuse, abuse, or normal wear and tear. Please retain your proof of purchase for any warranty claims.
Support and Contact
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Knightsbridge customer support. Refer to the official Knightsbridge website for the most up-to-date contact information.
Knightsbridge: www.mlaccessories.co.uk
