Introduction
This user manual provides essential information for the safe assembly, operation, and maintenance of your Erbesi MILKY White Crib. Please read these instructions carefully before assembly and retain them for future reference. Ensure all users are familiar with the contents of this manual.
Important Safety Warnings
- Always ensure all assembly fittings are correctly tightened. Regularly check for loose screws or parts.
- Do not use the crib if any part is broken, torn, or missing. Contact Erbesi for replacement parts.
- Keep the crib away from heat sources, open flames, and electrical outlets.
- Do not leave anything in the crib that could provide a foothold or present a danger of suffocation or strangulation.
- The mattress used with this crib should be of the correct size to prevent gaps that could entrap a child.
- Never use more than one mattress in the crib.
- The crib is intended for use by a child who cannot climb out of it and is less than 90 cm tall.
Package Contents
Before beginning assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact Erbesi customer support.
- Crib side panels (2)
- Crib end panels (2)
- Mattress support base (1)
- Casters with brakes (4)
- Assembly hardware kit (screws, nuts, Allen key)
- Instruction manual (this document)
Setup and Assembly
Assembly should be performed by an adult. Clear a spacious area for assembly. It is recommended to have two adults for easier assembly.
- Attach Casters: Securely attach the four casters to the bottom of the crib end panels using the provided screws. Ensure two casters with brakes are positioned on one end panel.
- Assemble End Panels: Connect the two end panels to one side panel using the provided hardware. Do not fully tighten screws yet.
- Insert Mattress Support: Carefully slide the mattress support base into the grooves on the inner side of the end panels. Ensure it is level and securely seated. The crib typically offers multiple mattress height settings. Choose the appropriate height for your child's age and development. For newborns, the highest position is generally recommended.
- Attach Second Side Panel: Connect the remaining side panel to the assembled structure.
- Tighten All Hardware: Once all parts are in place, systematically tighten all screws and fittings. Do not overtighten.
- Final Check: Gently shake the crib to ensure stability. Engage the brakes on the casters to prevent movement.
Operating Instructions
Caster Brakes
The crib is equipped with casters for easy movement. To secure the crib in place, press down on the lever located on each braked caster until it clicks. To release the brake, lift the lever upwards. Always engage the brakes when the crib is stationary and a child is inside.
Mattress Height Adjustment
The mattress support base can be adjusted to different heights. Refer to the assembly instructions for specific steps on how to safely lower or raise the mattress support. Always ensure the mattress support is securely locked into position at all four corners before placing a child in the crib. The highest position is for infants who cannot push up on their hands and knees. The lowest position is for children who can stand or climb.
Care and Maintenance
- Cleaning: Clean the crib regularly with a soft, damp cloth and mild soap. Avoid abrasive cleaners or strong detergents, as they may damage the finish. Dry thoroughly after cleaning.
- Inspections: Periodically inspect all screws, bolts, and fittings to ensure they are tight and secure. Tighten any loose hardware immediately.
- Storage: If storing the crib, disassemble it according to the reverse of the assembly instructions and store all parts in a dry, cool place. Keep all hardware in a sealed bag to prevent loss.
- Finish: The crib's finish is non-toxic. Avoid scratching or chipping the paint, as this can expose the underlying wood.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Crib is wobbly or unstable. | Loose hardware. | Check and tighten all screws and bolts. Ensure all parts are correctly aligned. |
| Casters do not lock or roll smoothly. | Brake mechanism obstructed or damaged; debris in caster wheel. | Clear any debris from the caster wheels. Ensure the brake lever is fully engaged/disengaged. If damaged, contact customer support for replacement. |
| Mattress support cannot be adjusted. | Obstruction or incorrect alignment. | Ensure no bedding or foreign objects are obstructing the adjustment mechanism. Re-read assembly instructions for correct adjustment procedure. |
Specifications
- Brand: Erbesi
- Model: 8050612381228
- Product Name: MILKY White Crib
- Material: Wood
- Color: White
- Features: Casters with brakes, adjustable mattress height, decorative end panel.
- Maximum Child Height: 90 cm
Warranty and Customer Support
Erbesi products are manufactured to high-quality standards. For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official Erbesi website. For technical assistance, missing parts, or any other inquiries, please contact Erbesi customer support.
Erbesi Official Website: www.erbesi.it
