1. Introduction and Safety Information
This manual provides essential instructions for the safe installation, operation, and maintenance of your Klarstein Aurica 60 Kitchen Extractor Hood. Please read this manual thoroughly before using the appliance and retain it for future reference.
Important Safety Instructions:
- Ensure the power supply voltage matches the rating label on the appliance.
- Installation must be performed by a qualified technician in accordance with local regulations.
- Do not operate the appliance if the power cord or plug is damaged.
- Regularly clean grease filters to prevent fire hazards.
- Maintain adequate ventilation in the room when the hood is operating simultaneously with other non-electric appliances.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
2. Product Overview
The Klarstein Aurica 60 is a wall-mounted kitchen extractor hood designed to efficiently remove cooking odors and grease from your kitchen. It features a powerful air flow, LED lighting, and touch controls for ease of use.
Figure 2.1: Front view of the Klarstein Aurica 60 Kitchen Extractor Hood.
Key Features:
- Air Flow Capacity: Up to 607 m³/h for effective ventilation.
- Control: Intuitive touch controls with 3 power levels.
- Lighting: Integrated LED lighting (2 x 1.5 W) for illuminating the cooking surface.
- Filtration: Aluminum anti-grease filters (dishwasher safe) and optional carbon filters for recirculation mode.
- Design: Wall-mounted canopy hood with a white finish.
Package Contents:
- 1 x Klarstein Aurica 60 Range Hood
- 2 x Chimney Liners
- Mounting material (screws, wall plugs, brackets)
- Instruction Manual
3. Setup and Installation
The Klarstein Aurica 60 is designed for wall-mounted installation. For detailed, step-by-step assembly instructions, please refer to the separate assembly guide included in your package. Ensure all safety precautions are followed during installation.
Installation Steps Overview:
- Preparation: Unpack all components and verify against the package contents list. Ensure the installation area is suitable and has access to a power outlet.
- Mounting: Secure the mounting bracket to the wall at the appropriate height above your cooking surface.
- Hood Attachment: Carefully lift and attach the extractor hood to the wall bracket.
- Ducting (if applicable): Connect the exhaust ducting to the hood and route it to the exterior vent.
- Chimney Installation: Install the decorative chimney liners over the ducting.
- Electrical Connection: Connect the hood to a suitable power supply.
Figure 3.1: Example of the extractor hood installed in a kitchen environment.
Note: If converting to recirculation mode, ensure carbon filters are installed (sold separately if not included). Refer to the carbon filter installation section in the detailed assembly guide.
4. Operating Instructions
The Klarstein Aurica 60 Extractor Hood features an intuitive touch control panel for easy operation of its functions.
Figure 4.1: Touch control panel for the extractor hood.
Control Panel Functions:
- Power Button (⏻): Press to turn the hood ON or OFF.
- Speed Adjustment (- / +): Adjust the fan speed between 3 available levels. Use the '-' button to decrease speed and '+' to increase speed.
- Light Button (☀): Press to turn the LED cooking surface lights ON or OFF.
Recommended Usage:
- Turn on the extractor hood a few minutes before you start cooking to create an airflow.
- Select the appropriate fan speed based on the intensity of cooking fumes.
- Allow the hood to operate for a few minutes after cooking to clear any residual odors.
5. Maintenance and Cleaning
Regular cleaning and maintenance of your extractor hood are crucial for optimal performance and safety. Always disconnect the appliance from the power supply before cleaning or performing maintenance.
Grease Filters (Aluminum):
The aluminum grease filters capture airborne grease particles. They should be cleaned regularly (approximately every 2-4 weeks, depending on usage) to maintain efficiency and prevent fire hazards.
- Removal: Open the glass panel and unlatch the grease filters.
- Cleaning: The filters are dishwasher safe. Alternatively, they can be washed by hand in hot water with a mild detergent. Ensure they are completely dry before reinstallation.
- Reinstallation: Insert the dry filters back into their slots and secure the latches.
Figure 5.1: Accessing the grease and carbon filters.
Carbon Filters (for Recirculation Mode):
If your hood is operating in recirculation mode, carbon filters are used to remove odors. These filters are typically not washable and need to be replaced periodically (every 3-6 months, depending on usage). Refer to the detailed assembly guide for specific replacement instructions.
Exterior Cleaning:
- Wipe the exterior surfaces with a soft cloth dampened with mild detergent.
- For the glass surface, use a glass cleaner and a soft cloth to avoid scratches.
- Do not use abrasive cleaners, steel wool, or harsh chemicals, as these can damage the finish.
6. Troubleshooting
Before contacting customer support, please consult the following troubleshooting guide for common issues:
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not turn on. | No power supply. Power cord not properly connected. | Check if the appliance is plugged in. Check the circuit breaker. |
| Low suction power. | Grease filters are clogged. Incorrect fan speed selected. Insufficient room ventilation. | Clean the grease filters. Increase the fan speed. Ensure windows or doors are slightly open for air intake. |
| Excessive noise. | Loose components. Improper installation of ducting. Fan obstruction. | Check for any loose parts and secure them. Verify ducting is correctly installed and sealed. Inspect fan for obstructions. |
| LED lights not working. | Light bulb failure. Electrical connection issue. | Contact customer support for light replacement. Check power supply to the hood. |
If the problem persists after attempting these solutions, please contact Klarstein customer support for further assistance.
7. Technical Specifications
| Model | Aurica 60 |
| Brand | KLARSTEIN |
| Mounting Type | Wall Mount |
| Air Flow Capacity | 607 m³/h (600 Cubic Feet Per Hour) |
| Number of Speeds | 3 |
| Noise Level | 71 Decibels |
| Controls Type | Touch |
| Light Source Type | LED (2 x 1.5 W) |
| Wattage | 150 watts |
| Voltage | 220 Volts |
| Filter Type | Aluminum Grease Filters, Optional Carbon Filters |
| Material | Stainless Steel |
| Product Dimensions (W x D x H) | 23.62 x 12.99 x 19.69 inches (60 x 33 x 50 cm approx.) |
| Item Weight | 15 kg (33 pounds) |
| Energy Efficiency Class | B |
8. Warranty and Customer Support
Klarstein products are manufactured with quality and reliability in mind. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official Klarstein website.
For technical assistance, spare parts, or any questions regarding your Klarstein Aurica 60 Extractor Hood, please contact Klarstein customer support. Contact details can typically be found on the Klarstein website or in your product documentation.
Online Support: www.klarstein.com/support (Example link, actual link may vary)