Audio-Technica AT6006R Safety Raiser Instruction Manual

1. Introduction

The Audio-Technica AT6006R Safety Raiser is an accessory designed to automatically lift the tonearm of a manual turntable at the end of a record. This mechanism helps protect the stylus from damage and reduces wear on both the stylus and the record. It features a highly sensitive release antenna and a hydraulic lift with a rubber lift bar, ensuring smooth and reliable operation.

Key features include:

• Automatic tonearm lift at the end of a record.
• Hydraulic lift with rubber bar for safe and smooth operation.
• Compatibility with various turntables due to adjustable height.
• Includes double-sided tape and spacers for installation.
• Height adjustment knob for precise setup.

2. Setup and Installation

Careful installation is crucial for the optimal performance of the AT6006R Safety Raiser. Ensure your turntable is powered off and the tonearm is secured before beginning installation.

2.1 Unpacking and Components

Verify that all components are present:

• AT6006R Safety Raiser unit
• Double-sided tape ×4
• Spacer ×2 (14 mm diameter × 12 mm height; 14 mm diameter × 24 mm height)

2.2 Placement and Mounting

1. Determine Placement: Position the Safety Raiser on the turntable plinth near the tonearm. The goal is for the tonearm to gently contact the raiser's antenna as it approaches the end of the record. Ensure there is sufficient clearance for the tonearm's movement and that the raiser does not interfere with the dust cover or other turntable components.
2. Measure Height: The Safety Raiser is designed to operate with tonearm heights between 27-39 mm from the plinth surface to the underside of the tonearm when it is resting on its support. Use the included spacers to achieve the correct height if necessary. The spacers have diameters of 14 mm and heights of 12 mm and 24 mm.
3. Attach Spacers (if needed): If additional height is required, stack the appropriate spacers and secure them together using the double-sided tape.
4. Secure the Unit: Clean the mounting surface on the turntable plinth. Apply one piece of double-sided tape to the base of the Safety Raiser (or the top spacer if used). Carefully place the unit in the determined position, ensuring it is stable and level. Press firmly for several seconds to secure it.

Figure 1: The AT6006R Safety Raiser installed next to a turntable tonearm. This image shows the compact design and how it integrates with a turntable setup.

Figure 2: Technical diagram illustrating the required dimensions for proper installation of the Safety Raiser. The base diameter is 14 mm, and the adjustable height range for the tonearm contact point is 27-39 mm.

2.3 Height Adjustment

Once mounted, fine-tune the height of the lift bar using the height adjustment knob. The goal is for the rubber lift bar to make contact with the tonearm just as the stylus reaches the run-out groove, lifting it clear of the record surface.

1. Place a record on the platter.
2. Manually move the tonearm to the run-out groove area of the record.
3. Adjust the height knob on the Safety Raiser so that the rubber lift bar is positioned to gently lift the tonearm when the antenna is triggered.
4. Test the operation by playing a record and observing the automatic lift at the end. Adjust as needed for smooth and reliable lifting.

3. Operating Instructions

The AT6006R Safety Raiser operates automatically once properly installed and adjusted.

1. Prepare for Playback: Before starting a record, ensure the Safety Raiser's lift mechanism is in its lowered, ready position. If it is already raised, gently push it down until it clicks into place.
2. Start Playback: Manually place the tonearm onto the record's lead-in groove as you normally would for your manual turntable.
3. Automatic Lift: As the record plays and the tonearm reaches the run-out groove, the tonearm will contact the Safety Raiser's antenna. This triggers the hydraulic lift, which will smoothly raise the tonearm off the record surface, protecting the stylus.
4. After Playback: Once the tonearm is lifted, you can manually return it to its rest. Remember to reset the Safety Raiser by gently pushing down the lift mechanism before playing the next record.

Important: Always ensure the Safety Raiser is reset to its lowered position before starting a new record to allow for proper operation.

4. Maintenance

The Audio-Technica AT6006R Safety Raiser requires minimal maintenance. Keep the unit clean and free of dust. Use a soft, dry cloth to wipe the surface. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish or the rubber lift bar.

Periodically check the double-sided tape to ensure the unit remains securely mounted. If the adhesive weakens, replace it with new double-sided tape.

5. Troubleshooting

If you experience issues with your AT6006R Safety Raiser, consider the following:

• Tonearm not lifting:
  • Ensure the Safety Raiser is properly reset (lowered) before playback.
  • Check if the tonearm is making proper contact with the antenna at the end of the record. Adjust the position of the Safety Raiser if necessary.
  • Verify the height adjustment. The lift bar must be positioned to engage the tonearm effectively.
• Tonearm lifting too early or too late:
  • Adjust the horizontal position of the Safety Raiser on the plinth. Move it slightly closer to the platter for later lift, or further away for earlier lift.
• Unit is unstable:
  • Ensure the double-sided tape is securely attached to a clean, flat surface. Replace the tape if it has lost its adhesive properties.
  • Verify that the spacers (if used) are correctly stacked and secured.

If problems persist, contact Audio-Technica customer support for further assistance.

6. Specifications

7. Warranty Information

The Audio-Technica AT6006R Safety Raiser is covered by a U.S. One-Year Limited End-User Warranty. For detailed terms and conditions, please refer to the official Audio-Technica warranty documentation or contact customer support.

8. Support and Contact

For further assistance, technical support, or warranty claims, please visit the official Audio-Technica website or contact their customer service department.

You can find more information and support resources by visiting the Audio-Technica Store on Amazon.