Relaxdays Wooden Pet Agility Seesaw Instruction Manual

1. Safety Instructions

Prioritize the safety and well-being of your pet during agility training. Adhere to the following guidelines:

• Supervision: Always supervise your dog during training sessions. Never leave your pet unattended with the seesaw.
• Health Check: Ensure your dog is in good physical condition and free from injuries before engaging in agility training. Consult a veterinarian if unsure.
• Feeding Schedule: Avoid training your dog on a full stomach. Wait at least 30 minutes after feeding before starting any exercise.
• Stable Surface: Place the seesaw on a flat, stable, and non-slippery surface. Uneven ground can cause instability.
• Proper Use: The seesaw is designed for dogs up to 50 kg (approximately 110 lbs). Do not exceed this weight limit.
• Weather Protection: While the seesaw features a rubber coat, it is recommended to store the seesaw indoors or protect it from harsh weather conditions when not in use to prolong its lifespan.
• Gradual Introduction: Introduce new obstacles and movements gradually to build your dog's confidence and prevent fear or injury.

2. Product Overview

The Relaxdays Wooden Pet Agility Seesaw is designed to enhance your dog's balance, concentration, and agility. It features a robust pinewood structure with a non-slip rubber coating for secure footing.

2.1. Key Features

• Durable Construction: Made from pinewood for stability.
• Non-Slip Surface: Equipped with a rubber coat to prevent slipping during use.
• Versatile Training: Suitable for both large and small dogs, with a maximum load capacity of 50 kg.
• Agility Component: Can be used as a standalone training tool or integrated into a larger obstacle course.

2.2. Dimensions & Weight

• Length: Approximately 180 cm (70.87 inches)
• Width: Approximately 30 cm (11.81 inches)
• Maximum Height: Approximately 54 cm (21.26 inches)
• Height of Middle Point: Approximately 30 cm
• Item Weight: Approximately 6.33 kg (13.93 lbs)

3. Setup and Assembly

The Relaxdays Pet Agility Seesaw is delivered in pieces and requires assembly. Follow the included assembly instructions carefully. A general overview of the assembly process is provided below:

1. Unpack Components: Carefully remove all parts from the packaging. Verify that all components listed in the assembly instructions are present.
2. Assemble Base: Construct the supporting base structure according to the diagrams in the assembly manual. Ensure all connections are secure.
3. Attach Seesaw Board: Connect the main seesaw board to the assembled base. Ensure the pivot points are correctly aligned and secured, allowing for smooth seesaw motion.
4. Final Check: Once assembled, gently test the seesaw to ensure it is stable and functions correctly before allowing your dog to use it.

4. Operating Instructions (Training Tips)

Effective training with the agility seesaw requires patience and positive reinforcement. Follow these tips to help your dog master the seesaw:

• Start Slowly: For shy or inexperienced dogs, begin by allowing them to walk over the board without the seesaw function. You can temporarily stabilize the seesaw to prevent it from tipping.
• Walk Alongside: Guide your dog by walking beside them as they cross the seesaw. This provides reassurance and direction.
• Use a Leash: Keep your dog on a leash, but avoid pulling. The leash is for guidance and safety, not for forcing movement.
• Control the Descent: Initially, hold the seesaw to control its descent, preventing it from falling too hard and startling your dog.
• Positive Reinforcement: Reward your dog with treats and praise for successful attempts. Keep training sessions positive and fun.
• Short Sessions: Conduct multiple short training sessions rather than one long one to maintain your dog's interest and prevent fatigue.
• Increase Difficulty Gradually: As your dog gains confidence, gradually reduce your assistance and allow the seesaw to function naturally.

5. Maintenance

Proper maintenance will extend the life of your Relaxdays Pet Agility Seesaw:

• Cleaning: Spot clean the seesaw as needed using a damp cloth. Avoid harsh chemicals that could damage the wood or rubber coating.
• Wood Protection: The seesaw is made of pinewood. For outdoor use, consider applying a water-resistant sealant to the wooden components before assembly to protect against moisture and prolong durability.
• Storage: Store the seesaw in a dry, protected area when not in use, especially during adverse weather conditions, to prevent damage and wear.
• Inspect Regularly: Periodically check all screws, bolts, and connections to ensure they are tight and secure. Inspect the wood for any signs of splitting or damage, and the rubber coating for excessive wear.

6. Troubleshooting

If you encounter issues with your seesaw, consider the following:

• Seesaw Slipping: If the seesaw slips on hard surfaces like concrete, place a non-slip mat underneath the base or use sandbags on the bottom support for added stability.
• Parts Not Fitting/Damaged: If wooden pieces are split, holes are not drilled correctly, or other parts are defective upon arrival, contact Relaxdays customer support for assistance or replacement parts.
• Rubber Coating Wear: Some shedding of the rubber beads may occur over time with use. If the coating is excessively deteriorating or affecting grip, contact customer support.

7. Specifications

8. Warranty and Support

For warranty information, product support, or to inquire about replacement parts, please refer to the contact details provided with your purchase or visit the official Relaxdays website. Keep your proof of purchase for any warranty claims.