Custom Dynamics PB-45-C Probeam LED Passing Lamps User Manual
Model: PB-45-C
1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Custom Dynamics PB-45-C 4.5in. Probeam LED Passing Lamps. These modern LED passing lamps are designed to enhance visibility and safety for your motorcycle.
2. Product Overview
The Custom Dynamics PB-45-C Probeam LED Passing Lamps feature a modern design with high lumen output for superior illumination. They are engineered for plug-and-play installation on most models.
Key Features:
- Modern LED passing lamp design
- 500 lumen output
- Plug and play installation
- Waterproof construction
Figure 2.1: Custom Dynamics PB-45-C Probeam LED Passing Lamps. These lamps feature a sleek, round design with a chrome finish and clear lens, showcasing the internal LED components.
3. Safety Information
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Always ensure the vehicle's power is disconnected before installation. Consult a qualified technician if you are unsure about any installation steps. Wear appropriate safety gear during installation.
4. Setup and Installation
The PB-45-C lamps are designed for plug-and-play installation. Follow these general steps for installation:
- Ensure the motorcycle's ignition is off and the battery is disconnected to prevent electrical shorts.
- Carefully remove the existing passing lamps from your motorcycle, if applicable.
- Connect the Custom Dynamics PB-45-C lamps to the motorcycle's wiring harness. For models manufactured before 2004, an adapter (part number 2001-1266) is required and sold separately.
- Securely mount the new LED passing lamps in the designated locations.
- Reconnect the battery and test the functionality of the new lamps.
- Adjust the lamp angle for optimal beam pattern and visibility.
For detailed vehicle-specific instructions, refer to your motorcycle's service manual.
5. Operation
Once installed, the Probeam LED Passing Lamps operate in conjunction with your motorcycle's existing lighting system. They are designed to provide additional forward and side illumination, enhancing your visibility to other road users and improving your view of the road.
- Turn on your motorcycle's ignition and headlight switch to activate the passing lamps.
- Ensure both lamps illuminate correctly.
- Periodically check the alignment of the lamps to ensure they are providing optimal light distribution without blinding oncoming traffic.
6. Maintenance
The Custom Dynamics PB-45-C LED Passing Lamps require minimal maintenance due to their durable LED technology and waterproof design.
- Cleaning: Clean the lens with a soft, damp cloth and mild soap. Avoid abrasive cleaners or solvents that could damage the lens or housing.
- Inspection: Periodically inspect the wiring and connections for any signs of wear, corrosion, or damage. Ensure mounting hardware remains secure.
- Waterproof Seal: Do not attempt to open the sealed lamp housing, as this will compromise its waterproof integrity and void the warranty.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamps do not illuminate | Loose connection, blown fuse, incorrect wiring, or adapter needed. | Check all connections, inspect vehicle's fuse box, verify wiring against motorcycle's diagram, ensure adapter 2001-1266 is used for pre-'04 models. |
| One lamp not working | Faulty lamp, loose connection to one lamp. | Check connection to the non-working lamp. If still not working, contact Custom Dynamics support. |
| Flickering lamps | Unstable power supply, loose connection. | Ensure stable voltage from the motorcycle's electrical system. Check all connections for tightness. |
8. Specifications
| Attribute | Detail |
|---|---|
| Brand | Custom Dynamics |
| Model Number | PB-45-C |
| Lamp Size | 4.5 inches |
| Light Output | 500 lumens |
| Color | Chrome |
| Lens Color | Clear |
| Special Feature | Waterproof |
| Item Weight | 2.85 pounds |
| UPC | 644978551043 |
9. Warranty and Support
For warranty information and technical support, please contact Custom Dynamics directly. Refer to their official website or the product packaging for the most current contact details and warranty policy.
Website: www.customdynamics.com
