Introduction
This manual provides essential instructions for the safe assembly, operation, and maintenance of your Intex Seahawk 3 Inflatable Boat Set. Please read all instructions carefully before use and retain this manual for future reference.
The Intex Seahawk 3 is designed for recreational use on calm waters, suitable for up to three persons. It features heavy-duty PVC construction, an I-beam floor, and three air chambers for durability and stability.
Safety Information
WARNING: This is not a life-saving device. Do not leave child unattended while device is in use. See product for additional warnings.
- Always wear a U.S. Coast Guard approved personal flotation device (PFD).
- Do not exceed the maximum weight capacity of 790 pounds (360 kg) or the maximum number of persons (3 adults).
- Never operate the boat under the influence of alcohol or drugs.
- Be aware of weather conditions and water currents. Avoid using in strong winds, rough waters, or during storms.
- Always check the boat for damage or leaks before each use.
- Keep away from sharp objects, hot surfaces, and open flames.
- Ensure all air chambers are properly inflated before entering the water.
- Children should only use the boat under competent adult supervision.
Package Contents
Verify that all components are present in your Intex Seahawk 3 package:
- 1 x Intex Seahawk 3 Inflatable Boat
- 2 x 48-inch Aluminum Oars
- 1 x Intex High-Output Hand Pump
- 1 x Repair Patch Kit (typically included)
- 1 x Instruction Manual
Image: The Intex Seahawk 3 boat set packaging, illustrating the inflatable boat, aluminum oars, and high-output pump included in the package.
Setup
1. Inflation
- Unfold the boat on a clean, flat surface free of sharp objects.
- Locate the Boston valves on each air chamber. The Seahawk 3 has three main air chambers.
- Open the outer cap of the Boston valve. Insert the nozzle of the high-output hand pump into the valve.
- Inflate each chamber sequentially until it is firm to the touch but not hard. Do not overinflate. The I-beam floor should be inflated last.
- Once inflated, quickly remove the pump nozzle and close the inner and outer caps of the Boston valve securely. Ensure all valves are tightly sealed.
Image: A close-up view of the Intex Seahawk 3 inflatable boat, showing the high-output pump and one of the aluminum oars, ready for inflation and assembly.
2. Oar Assembly
- Connect the two sections of each aluminum oar by aligning the push-button with the hole and snapping them together.
- Insert the assembled oars into the oar locks located on the sides of the boat. Secure them in place.
Image: A detailed view of the Intex Seahawk 3 boat, highlighting the assembled aluminum oars securely placed in the oar locks on the side of the inflatable boat.
Operating Instructions
1. Launching the Boat
- Carefully carry the inflated boat to the water's edge. Avoid dragging it over rough surfaces.
- Ensure the water is deep enough to prevent the boat from scraping the bottom.
- Enter the boat one person at a time, distributing weight evenly.
2. Rowing
- Sit comfortably on the inflatable seats.
- Place your hands on the oar handles and use a smooth, coordinated motion to propel the boat.
- The oar holders allow for easy rowing and can be used to secure the oars when not in use.
3. General Use
- Always maintain a safe distance from other watercraft and swimmers.
- Avoid standing up in the boat while on the water to maintain stability.
- If equipped, use the grab rope for assistance when entering or exiting the boat, or for holding onto in choppy water.
Image: Three individuals are shown enjoying a leisurely ride in the Intex Seahawk 3 inflatable boat on a calm body of water, demonstrating its capacity and use.
Maintenance
1. Cleaning
- After each use, rinse the boat thoroughly with fresh water to remove salt, sand, or dirt.
- Use a mild soap solution and a soft cloth to clean stubborn stains. Avoid harsh chemicals or abrasive cleaners.
- Ensure the boat is completely dry before deflating and storing to prevent mildew.
2. Storage
- Deflate all air chambers by opening the Boston valves.
- Fold the boat loosely to avoid sharp creases.
- Store the boat in a cool, dry place, away from direct sunlight and extreme temperatures.
3. Repairing Leaks
- If a small leak occurs, locate it by applying soapy water to the inflated surface; bubbles will indicate the leak.
- Clean and dry the area around the leak.
- Apply a repair patch from the included kit according to the kit's instructions. Allow sufficient time for the adhesive to cure before reinflating.
Troubleshooting
- Boat loses air quickly: Check all Boston valves to ensure they are tightly closed. Inspect the boat surface for punctures or seam leaks. Use the repair kit for small punctures.
- Difficulty inflating: Ensure the pump nozzle is fully inserted into the Boston valve and the valve's inner cap is open during inflation.
- Oars do not stay in place: Verify that the oars are correctly assembled and securely placed in the oar locks.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 2x68380EP |
| Capacity | 3 Persons |
| Maximum Weight Capacity | 790 pounds (360 kg) |
| Dimensions (L x W x H) | 116 x 54 x 17 inches (295 x 137 x 43 cm) |
| Material | Heavy-duty PVC |
| Air Chambers | 3 (including I-beam floor) |
| Included Accessories | 2 Aluminum Oars, High-Output Hand Pump |
| Color | Green |
Product Overview Video
Video: An official product video from Spreetail showcasing the Intex Seahawk 3 inflatable boat in various outdoor settings, demonstrating its features and use. This video provides a visual guide to the boat's capabilities and design.
Warranty and Support
For warranty information and customer support regarding your Intex Seahawk 3 Inflatable Boat Set, please refer to the documentation included with your purchase or contact the retailer directly. The product is manufactured by Intex.
For purchases made through Spreetail, a 30-day easy returns policy and customer support are typically available. Please check your purchase details for specific terms.
