Beatfoxx FA-50 Soundspark Portable Bluetooth Speaker Instruction Manual

1. Introduction

Thank you for purchasing the Beatfoxx FA-50 Soundspark Portable Bluetooth Speaker. This device combines a portable Bluetooth speaker with an LED flame effect, designed for outdoor and indoor use. Please read this manual carefully before operating the device to ensure proper use and to prevent damage.

2. Safety Information

Observe the following safety guidelines to ensure safe operation and to prevent damage to the device or injury to yourself.

• Do not expose the device to extreme temperatures, direct sunlight, or high humidity.
• Keep the device away from water and other liquids. While the device is designed to withstand small splashes (IP65), it is not fully submersible.
• Do not attempt to disassemble, repair, or modify the device yourself. Contact qualified service personnel for any repairs.
• Use only the provided Micro USB cable for charging.
• Keep out of reach of children.
• Dispose of the device and its battery responsibly according to local regulations.

3. Package Contents

Ensure all items are present in the package:

• Beatfoxx FA-50 Soundspark Portable Bluetooth Speaker
• Micro USB Charging Cable
• Instruction Manual (this document)

4. Product Overview

Familiarize yourself with the components and controls of your FA-50 Soundspark speaker.

Image: Top view of the Beatfoxx FA-50 Soundspark speaker, highlighting the control panel with power, light, play/pause, and volume buttons.

4.1 Control Panel

• Power Button (⏻): Press and hold to power on/off.
• Light Button (💡): Press to turn the LED flame light on/off.
• Play/Pause Button (⏸): Press to play or pause audio.
• Volume Down / Previous Track Button (-): Press to decrease volume. Press and hold to go to the previous track.
• Volume Up / Next Track Button (+): Press to increase volume. Press and hold to go to the next track.

4.2 Ports and Indicators

• Micro USB Port: For charging the internal battery.
• LED Indicator: Shows charging status and Bluetooth pairing status.
• 1/4 inch Camera Thread: Located on the bottom for mounting options.

5. Setup

5.1 Charging the Battery

1. Connect the Micro USB charging cable to the Micro USB port on the speaker.
2. Connect the other end of the cable to a USB power adapter (not included) or a computer's USB port.
3. The LED indicator will illuminate to show charging status. It will change color or turn off when fully charged.
4. A full charge takes approximately 3-4 hours. The battery provides up to 13 hours of playback at background volume.

5.2 Powering On/Off

• To power on, press and hold the Power Button (⏻) for a few seconds until you hear an audible prompt and the LED indicator flashes.
• To power off, press and hold the Power Button (⏻) again for a few seconds until you hear an audible prompt and the LED indicator turns off.

6. Operating Instructions

6.1 Bluetooth Pairing

To connect your FA-50 Soundspark speaker to a Bluetooth-enabled device:

1. Ensure the speaker is powered on and in pairing mode (LED indicator will be flashing rapidly).
2. Enable Bluetooth on your smartphone, tablet, or other audio device.
3. Search for available Bluetooth devices. The speaker will appear as "FA-50 Soundspark" or similar.
4. Select "FA-50 Soundspark" from the list to pair. Once paired, the LED indicator will stop flashing and remain solid, and you will hear a confirmation sound.
5. If pairing fails, turn off the speaker and your device's Bluetooth, then repeat the steps.

Image: The Beatfoxx FA-50 Soundspark speaker next to a smartphone, illustrating Bluetooth connectivity for music playback.

6.2 Music Playback

Once paired, you can control music playback directly from the speaker or your connected device:

• Play/Pause: Press the Play/Pause Button (⏸).
• Volume Adjustment: Press the + button to increase volume, and the - button to decrease volume.
• Next/Previous Track: Press and hold the + button for the next track, and the - button for the previous track.
• Incoming Calls: The speaker will automatically pause music playback for incoming calls and resume once the call ends.

6.3 LED Flame Light Function

The LED flame light can be operated independently of the speaker function.

• To turn the LED flame light on or off, press the Light Button (💡).
• The light provides a realistic flame effect and does not generate heat.

Image: The Beatfoxx FA-50 Soundspark speaker displaying its LED flame effect, providing ambient lighting.

7. Maintenance

7.1 Cleaning

• Ensure the device is powered off and disconnected from any power source before cleaning.
• Wipe the exterior with a soft, dry cloth.
• Do not use abrasive cleaners, solvents, or strong chemicals.

7.2 Storage

• Store the speaker in a cool, dry place away from direct sunlight and extreme temperatures.
• If storing for an extended period, charge the battery periodically (e.g., every 3 months) to maintain battery health.

8. Troubleshooting

9. Specifications

10. Warranty and Support

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for warranty claims.