Intel DC P4610 Series 3.2TB Solid State Drive User Manual

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your Intel DC P4610 Series 3.2TB Solid State Drive. Designed for demanding service levels and cloud workloads, this SSD offers high performance and reliability. Please read this manual thoroughly before proceeding with installation or use.

2. Product Overview

The Intel DC P4610 Series 3.2TB SSD is an internal solid-state drive utilizing a U.2 (SFF-8639) interface with PCI Express 3.1 x4 connectivity. It features 3D NAND technology and 256-bit encryption for data security. This drive is engineered to enhance storage performance in compatible server and computer systems.

Figure 1: A silver Intel 3D NAND SSD, model DC P4610 Series, shown from the top, featuring the Intel logo and product branding.

Key Features:

• Storage Capacity: 3.20 TB
• Encryption Standard: 256-bit
• Maximum Read Transfer Rate: 3.13 GB/s
• Maximum Write Transfer Rate: 2.93 GB/s
• Drive Interface: U.2 (SFF-8639)
• Form Factor: 2.5-inch internal drive

3. Setup and Installation

The Intel DC P4610 Series SSD is designed for internal installation in compatible server and desktop systems. Always ensure proper anti-static precautions are taken when handling the drive.

Installation Steps:

1. Prepare Your System: Power down your computer or server and disconnect all power cables. Open the system chassis according to the manufacturer's instructions.
2. Locate a Compatible Bay: Identify an available 2.5-inch drive bay and a U.2 port on your motherboard or PCIe adapter card. The drive requires a PCI Express 3.1 x4 interface.
3. Install the SSD: Carefully slide the Intel DC P4610 SSD into the 2.5-inch drive bay. Secure it with screws if required by your system's chassis.
4. Connect Cables: Connect the U.2 (SFF-8639) cable from the SSD to the corresponding port on your motherboard or PCIe adapter. Ensure the connection is firm.
5. Secure and Close: Once the drive is securely installed and connected, close the system chassis and reconnect all power cables.
6. Initial Boot and Configuration: Power on your system. Access the BIOS/UEFI settings to confirm the drive is detected. You may need to initialize and partition the drive using your operating system's disk management tools before use.

Compatible Systems: This SSD is compatible with various Intel Rack Server Systems (e.g., R1208WFTYS, R2208WF0ZS), Intel Compute Modules (e.g., HNS2600BPB24), and Intel Dual-Socket Server Boards (e.g., S2600STB, S2600WFQ).

4. Operating the SSD

Once installed and recognized by your system, the Intel DC P4610 SSD operates like any other storage device. Its high-speed interface provides rapid data access and transfer rates.

Key Operational Aspects:

• Operating System Integration: Ensure your operating system has the necessary drivers for NVMe (Non-Volatile Memory Express) devices to fully utilize the PCIe interface. Most modern operating systems include these drivers by default.
• Data Management: Use standard operating system tools for file management, data transfer, and backup.
• Performance Monitoring: Utilize system monitoring tools to observe drive performance and health.

5. Maintenance

Solid State Drives generally require less maintenance than traditional hard drives. However, some practices can help ensure optimal performance and longevity.

Maintenance Guidelines:

• Firmware Updates: Periodically check the Intel support website for firmware updates for the DC P4610 Series SSD. Firmware updates can improve performance, stability, and address potential issues.
• Drive Health Monitoring: Use S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) tools to monitor the health and status of your SSD.
• Avoid Excessive Writes: While SSDs are robust, extremely high write workloads over extended periods can reduce their lifespan. This drive is designed for demanding environments, but general best practices apply.
• Temperature Management: Ensure adequate airflow within your system chassis to prevent the SSD from operating at excessively high temperatures, which can impact performance and longevity.

6. Troubleshooting

If you encounter issues with your Intel DC P4610 Series SSD, refer to the following troubleshooting steps.

Common Issues and Solutions:

• SSD Not Detected:
  • Verify that the U.2 cable is securely connected to both the SSD and the motherboard/adapter.
  • Check BIOS/UEFI settings to ensure the U.2/PCIe slot is enabled and the drive is recognized.
  • Ensure your motherboard's BIOS/UEFI is updated to the latest version.
  • Test the SSD in a different compatible system or with a different U.2 cable/port if possible.
• Poor Performance:
  • Ensure your operating system is configured for optimal SSD performance (e.g., TRIM enabled).
  • Check for background processes or applications that might be consuming disk I/O.
  • Verify that the SSD is connected to a PCIe 3.1 x4 slot to achieve maximum transfer rates.
  • Update SSD firmware to the latest version.
• Operating System Not Booting from SSD:
  • Confirm that the SSD is set as the primary boot device in your BIOS/UEFI settings.
  • Ensure the operating system was installed correctly on the SSD.

If issues persist, consult the Intel support website or contact technical support.

7. Specifications

8. Warranty and Support

The Intel DC P4610 Series 3.2TB Solid State Drive comes with a 5-Year Limited Warranty from Intel. For detailed warranty terms and conditions, please refer to the official Intel warranty documentation or visit the Intel support website.

For technical assistance, product information, or warranty claims, please contact Intel Customer Support through their official channels. Keep your proof of purchase and the product's model number (SSDPE2KE032T801) readily available when seeking support.

Intel Support Website: https://www.intel.com/content/www/us/en/support/products/memory-storage/solid-state-drives.html