Introduction
This manual provides essential information for the safe and efficient operation of your QILIVE Q.1893 Radiorecorder. Please read this manual thoroughly before using the device and retain it for future reference. The Q.1893 is a versatile radiorecorder featuring Bluetooth connectivity and a 2-channel speaker configuration.
Safety Information
- Do not expose the device to rain or moisture to prevent fire or electric shock.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way.
Product Overview
The QILIVE Q.1893 Radiorecorder is designed for audio playback, offering both radio and Bluetooth streaming capabilities. It features a robust design with integrated speakers.
Figure 1: Front view of the QILIVE Q.1893 Radiorecorder. The device is black with two prominent circular speaker grilles, each illuminated with a blue light, indicating power or active status. Handles are visible on the top for portability.
The device typically includes controls for power, volume, mode selection (radio/Bluetooth), and tuning/track navigation. Specific button layouts may vary, refer to the labels on your unit.
Setup
1. Power Connection
- Ensure the radiorecorder is placed on a stable, flat surface.
- Locate the power input port on the device, usually at the rear.
- Connect the provided power cable to the device and then plug the other end into a standard electrical outlet.
- The device is now ready to be powered on.
2. Initial Power On
- Press the Power button, typically located on the front or top panel.
- An indicator light, often blue as seen in Figure 1, will illuminate to confirm the device is powered on.
Operating Instructions
1. Adjusting Volume
- Use the Volume Up and Volume Down buttons or a rotary knob to adjust the audio output level.
2. Bluetooth Pairing
- Press the Mode button to select Bluetooth mode. The device will typically emit an audible prompt or display "BT" on a screen, and the indicator light may flash.
- On your mobile device (smartphone, tablet, etc.), enable Bluetooth and search for available devices.
- Select "QILIVE Q.1893" or a similar name from the list of found devices.
- Once paired, the device will confirm with an audible tone or a steady indicator light. You can now stream audio from your mobile device.
3. Radio Operation
- Press the Mode button to select FM/AM radio mode.
- Extend the telescopic antenna for optimal reception.
- Use the Tune or Scan buttons to find radio stations. The Scan function will automatically search and save available stations.
- Use the Previous/Next buttons to navigate through saved stations or fine-tune frequencies.
Maintenance
1. Cleaning
- Always unplug the device from the power outlet before cleaning.
- Use a soft, dry cloth to wipe the exterior surfaces.
- Do not use liquid cleaners, abrasive cleaners, or chemical sprays, as these can damage the finish or internal components.
2. Storage
- When not in use for extended periods, store the radiorecorder in a cool, dry place, away from direct sunlight and extreme temperatures.
- It is recommended to store the device in its original packaging to protect it from dust and physical damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable not connected properly; power outlet not active. | Check power cable connection; try a different power outlet. |
| No sound | Volume too low; incorrect mode selected; device not paired (Bluetooth). | Increase volume; ensure correct mode (Bluetooth/Radio) is selected; re-pair Bluetooth device. |
| Poor radio reception | Antenna not extended; weak signal. | Fully extend the telescopic antenna; reposition the device for better signal. |
| Bluetooth device cannot pair | Radiorecorder not in pairing mode; Bluetooth on mobile device is off or already connected to another device. | Ensure radiorecorder is in Bluetooth pairing mode; turn off and on Bluetooth on your mobile device; disconnect from other Bluetooth devices. |
Specifications
- Brand: QILIVE
- Model Name: Q.1893
- Model Number: C1076041
- Manufacturer: QILIVE
- Model Year: 2019
- Speaker Channel Configuration: 2
- Bluetooth Technology: Compatible
- Audio Recording: Not included
- First Available Date: 21 February 2020
Warranty and Support
For warranty information and customer support, please refer to the warranty card included with your product or contact your retailer. QILIVE provides support for its products to ensure customer satisfaction. Keep your proof of purchase for any warranty claims.
For further assistance, please visit the official QILIVE website or contact their customer service department.
