E-flite Tail Set: Mini Convergence (EFL9302) Instruction Manual

Introduction

This manual provides essential instructions for the E-flite Tail Set, model EFL9302, specifically designed for the Mini Convergence aircraft. It covers important safety guidelines, installation procedures, maintenance tips, and product specifications to ensure proper use and longevity of your aircraft component.

Safety Information

WARNING:

Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. The product manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

What's in the Box

• Tail Set: Mini Convergence

Setup and Installation

1. Preparation: Ensure your Mini Convergence aircraft is powered off and the battery is disconnected before beginning installation. Clear your workspace and gather any necessary tools (e.g., small screwdriver, adhesive if required).
2. Remove Existing Tail Components (if applicable): Carefully detach any damaged or old tail components from the aircraft fuselage. Refer to your aircraft's main manual for specific removal instructions.
3. Align New Tail Set: Position the new E-flite Tail Set pieces onto the designated areas of the Mini Convergence fuselage. Ensure proper orientation and alignment with the aircraft's structure. The pieces should fit snugly.
4. Secure the Tail Set: Depending on the aircraft design, secure the tail set using the provided fasteners or recommended adhesive. Apply adhesive sparingly and allow adequate drying time if used. Ensure all connections are firm and stable.
5. Verify Control Surface Movement: Once installed, gently check the movement of any integrated control surfaces (e.g., rudders, elevators) on the tail set. Ensure they move freely and without obstruction. Reconnect the battery and perform a control surface test with your transmitter to confirm correct operation and direction.

Always refer to the complete Mini Convergence aircraft manual for detailed assembly and setup instructions, as this tail set is a replacement part.

Operating Considerations

The E-flite Tail Set is a structural and aerodynamic component of your Mini Convergence aircraft. Its operation is integral to the overall flight performance and stability. Once correctly installed, the tail set functions passively to provide lift, stability, and control authority through its associated control surfaces (if any). Ensure all control linkages are properly connected and calibrated before flight.

Maintenance

• Regular Inspection: Before each flight, visually inspect the tail set for any signs of damage, cracks, or loose connections.
• Cleaning: If necessary, gently clean the tail set with a soft, damp cloth. Avoid using harsh chemicals that could damage the foam material.
• Storage: Store the aircraft in a safe place, away from direct sunlight and extreme temperatures, to prevent material degradation.
• Repair: Minor damage to foam can often be repaired with foam-safe adhesive. For significant damage, replacement of the tail set is recommended.

Troubleshooting

• Loose Tail Set: If the tail set feels loose after installation, re-check all fasteners or adhesive points. Ensure they are securely attached.
• Incorrect Control Surface Movement: If control surfaces on the tail (e.g., elevator, rudder) do not move correctly, verify that linkages are properly connected to the servos and that the servo directions are correctly set on your transmitter.
• Visible Damage: Any visible cracks or deformities should be addressed immediately. Depending on severity, repair with foam-safe glue or replace the component.

Specifications

Warranty and Support

For warranty information, technical support, or replacement parts, please contact Horizon Hobby, LLC, the manufacturer of E-flite products. Refer to their official website or the original aircraft manual for contact details and specific warranty terms applicable to your region.

Horizon Hobby, LLC: www.horizonhobby.com