Genie GT912 Visor Remote Control User Manual

Introduction

This manual provides instructions for the Genie GT912 Compatible Visor Remote Control. This remote is designed to operate Genie garage door openers that utilize 9 or 12-dip switches, typically found in models manufactured between 1982 and 1992.

The GT912 remote offers a convenient way to control your compatible Genie garage door opener.

Product Overview

Image of the Genie GT912 remote control, showing its compact design and single button. A visor clip is attached to the back.

The Genie GT912 remote control features a compact design with a single button for operation. It includes a visor clip for easy attachment within your vehicle. The remote is powered by a 9V battery and utilizes dip switches for programming.

Setup and Programming

To program your Genie GT912 remote control, you must match its internal dip switch settings to those of your existing Genie garage door opener remote or the garage door opener unit itself. This remote is compatible with both 9 and 12-dip switch systems.

1. Locate Existing Dip Switches: Identify the dip switches on your current working Genie remote control or directly on your garage door opener unit. These switches are typically small, numbered toggles that can be set to three positions: ON (+), OFF (0), or MIDDLE (-). Note down the exact sequence of these switch positions.
2. Access GT912 Dip Switches: Open the battery compartment or the casing of your new Genie GT912 remote control. The dip switches will be visible inside.
3. Match Switch Positions: Using a small screwdriver or a similar pointed tool, carefully adjust the dip switches on your new GT912 remote to precisely match the sequence you noted from your existing remote or opener unit. Ensure each switch is set to the correct ON (+), OFF (0), or MIDDLE (-) position.
4. Install Battery: Insert a fresh 9V battery into the battery compartment of the GT912 remote, observing the correct polarity (+/-).
5. Close Casing: Securely close the battery compartment or casing of the remote.
6. Test Operation: Stand within range of your garage door opener and press the button on the GT912 remote. The garage door should activate. If it does not, re-verify the dip switch settings and battery installation.

Note: The GT912 remote is compatible with Genie Garage Door Opener models from 1982 to 1992, including: CH125, CH130, GS980, GS9800, GS880, GS8800, GS820, GS8200, GS720, GS850, GS800, PRO82, PRO98, PRO88, PRO90, Blue Max, GG1950, GG1810, GS900, GS920, GS940, GS975, GS810, GS810A, GS815, GS840, GS210, GS250, SP99, SP129, SP229, LD100, LD500, LD100A, LD550A, LAD125, LAD555, CM6000, CM6000A, CM60, CM70, CM80, CM60S, CM70S, CM80S, PMX60, PMX70, PMX80, PRO83, PRO93, PRO88S, PRO98S, CM7500, CM8500, CM7500S, CM8500S, SD9500, SD9000, SD8000, SD2500, SD5000, GXL/GX/G Series 9500 9000 8000 2500 5000 10000.

Operating Instructions

Once programmed, operating your Genie GT912 remote control is straightforward:

1. Ensure you are within a reasonable operating range of your garage door opener.
2. Press and release the single button on the GT912 remote control.
3. The garage door should begin to open or close. Pressing the button again during operation will stop the door.

Maintenance

The primary maintenance for your Genie GT912 remote control involves battery replacement.

Battery Replacement

The remote uses one 9V battery. If the remote's range decreases significantly or the LED indicator (if present) does not light up, it is likely time to replace the battery.

1. Open the battery compartment cover on the back of the remote control.
2. Remove the old 9V battery.
3. Insert a new 9V battery, ensuring the positive (+) and negative (-) terminals are correctly aligned.
4. Replace the battery compartment cover securely.
5. Test the remote's operation.

Troubleshooting

If your Genie GT912 remote control is not functioning as expected, consider the following troubleshooting steps:

• Remote Not Responding:
  • Check the battery. Replace it with a fresh 9V battery if necessary.
  • Verify the dip switch settings. Ensure they precisely match your garage door opener's settings.
  • Ensure you are within the operating range of the garage door opener.
  • Check for any obstructions between the remote and the garage door opener's receiver.
• Limited Operating Range:
  • Replace the 9V battery. A weak battery is a common cause of reduced range.
  • Check for potential sources of radio frequency interference in the area.
• Door Opens/Closes Intermittently:
  • Re-check the dip switch settings for any loose or incorrect positions.
  • Ensure the battery connections are secure.

Specifications

Warranty and Support

Specific warranty information for the Genie GT912 Compatible Visor Remote Control is not provided in this manual. For details regarding warranty coverage, returns, or technical support, please refer to the product packaging or contact Genie customer service directly.

You may also visit the official Genie website for further assistance and product information.