Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Scosche VWDSM2 3-in-1 Car Mount. This versatile mount system is designed to securely hold your mobile device in your vehicle using a suction cup base for windows and dashboards, or a vent clip for air vents. It features adjustable arms to accommodate various smartphone sizes and 360-degree rotation for optimal viewing angles.
Safety Information
- Ensure the mount is securely installed before placing a device in it.
- Do not install the mount in a location that obstructs your view of the road, mirrors, or vehicle controls.
- Avoid adjusting the mount or your device while driving. Make all adjustments before starting your journey.
- Do not expose the mount to extreme temperatures for prolonged periods, as this may affect its performance.
- Keep the mount away from airbags or areas where it could interfere with airbag deployment.
Package Contents
Please verify that all components are present in your package:
- Adjustable Device Holder
- Suction Cup Base (with StickGrip™ technology)
- Vent Clip Attachment
Image: The Scosche VWDSM2 3-in-1 Car Mount, featuring the adjustable device holder attached to the suction cup base.
Image: The vent clip attachment, designed to securely fasten the device holder to vehicle air vents.
Setup and Installation
Attaching the Device Holder to the Base
- Locate the ball joint on either the suction cup base or the vent clip.
- Unscrew the collar nut from the back of the adjustable device holder.
- Place the collar nut over the ball joint.
- Push the device holder onto the ball joint until it is fully seated.
- Tighten the collar nut to secure the device holder in place. Do not overtighten.
Option 1: Window or Dash Mount (Using Suction Cup Base)
- Choose a clean, flat, and smooth surface on your windshield or dashboard. Ensure the area is free from dust and debris.
- Press the suction cup firmly against the chosen surface.
- Flip the lever on the suction cup base down to create a strong vacuum seal.
- Verify that the mount is securely attached before proceeding.
Image: The Scosche VWDSM2 mount securely installed on a vehicle's dashboard, providing a stable platform for a smartphone.
Image: The Scosche VWDSM2 mount attached to a car windshield, positioned for clear visibility without obstructing the driver's view.
Option 2: Vent Mount (Using Vent Clip Attachment)
- Select a sturdy, horizontal or vertical air vent slat in your vehicle.
- Gently push the vent clip attachment onto the chosen vent slat until it is firmly seated. Ensure the clip's prongs are fully engaged with the vent slat.
- Verify that the mount is stable and does not wobble before placing your device.
Image: The Scosche VWDSM2 mount attached to a vehicle's air vent, providing an alternative mounting location.
Operating Instructions
Inserting Your Mobile Device
- Gently pull apart the adjustable side arms of the device holder.
- Place your smartphone into the holder, ensuring it is centered and the arms securely grip the device. The arms can expand up to 3.5 inches wide.
- Release the arms slowly to allow them to close around your device, holding it firmly.
Image: A smartphone is shown securely held within the adjustable arms of the Scosche VWDSM2 car mount.
Adjusting Viewing Angle
- The device holder features a 360-degree rotating ball joint. Loosen the collar nut slightly to adjust the angle.
- Rotate your device to achieve either portrait or landscape orientation.
- Once the desired angle is set, tighten the collar nut to lock it in position.
Maintenance
- Cleaning the Suction Cup: If the suction cup loses its grip, rinse it with warm water and let it air dry. This will restore its StickGrip™ properties.
- General Cleaning: Wipe the mount with a soft, damp cloth to remove dust and grime. Avoid using harsh chemicals or abrasive cleaners.
- Storage: When not in use for extended periods, store the mount in a cool, dry place away from direct sunlight.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Mount not sticking to surface (suction cup) | Surface is dirty or uneven; suction cup is dirty or dry. | Clean the mounting surface thoroughly. Rinse the suction cup with warm water and let it air dry before re-applying. Ensure the lever is fully engaged. |
| Mount is loose on air vent | Vent clip not fully engaged; vent slats are too thin or flexible. | Ensure the vent clip is pushed firmly onto a sturdy vent slat. Try a different vent location if necessary. |
| Device not held securely | Adjustable arms not properly gripping the device. | Ensure the device is centered and the arms are fully closed around it. The device width must be within the 3.5-inch limit. |
| Mount angle keeps shifting | Collar nut on ball joint is loose. | Tighten the collar nut on the ball joint to secure the desired viewing angle. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | VWDSM2 |
| Mounting Types | Window, Dashboard, Air Vent |
| Device Compatibility | Smartphones up to 3.5 inches wide (e.g., Apple iPhone, Samsung Galaxy, Google Pixel, LG, OnePlus, etc.) |
| Rotation | 360-degree adjustable viewing angle |
| Dimensions (Product) | 3.05 x 2.75 x 7.1 inches |
| Weight (Item) | 4.6 ounces |
| Special Features | Adjustable, Portable, Removable, StickGrip™ Suction |
Warranty and Support
The Scosche VWDSM2 Car Mount is backed by Scosche's 3-year warranty and lifetime technical support.
For further assistance or to view the original PDF user manual, please visit the official Scosche support website or refer to the provided PDF document:
- Official User Manual (PDF): Download PDF
- Scosche Support: For additional support, please visit the Scosche Brand Store or their official website.