Geko G00950 Fuel Nozzle with LCD Digital Flow Meter User Manual

1. Introduction

This manual provides comprehensive instructions for the safe and effective operation and maintenance of the Geko G00950 Fuel Nozzle with LCD Digital Flow Meter. This durable and high-performance tool is designed for precise measurement and dispensing of various liquids, ensuring reliable performance.

Please read this manual thoroughly before using the product to ensure proper function and to prevent damage or injury. Keep this manual for future reference.

2. Product Overview

The Geko G00950 combines a robust fuel dispensing nozzle with an integrated LCD digital flow meter, allowing for accurate measurement of dispensed liquid volumes. It is constructed from high-quality materials for longevity and consistent performance.

Figure 1: Front view of the Geko G00950 Fuel Nozzle with LCD Digital Flow Meter, showing the nozzle, handle, digital display, and an included threaded fitting.

Figure 2: Side view of the Geko G00950 Fuel Nozzle, illustrating the ergonomic handle and the overall design of the dispensing mechanism.

3. Safety Information

Always observe the following safety precautions to prevent injury or damage to the product:

• Ensure the nozzle is securely connected to the hose before dispensing.
• Do not use the nozzle for liquids other than those it is designed for.
• Wear appropriate personal protective equipment (PPE) when handling fuels or other liquids.
• Avoid dropping or subjecting the device to severe impacts, as this may damage the digital meter.
• Keep out of reach of children.

4. Setup

Follow these steps to set up your Geko G00950 Fuel Nozzle:

1. Unpacking: Carefully remove all components from the packaging. Verify that all parts are present and undamaged.
2. Connection:
   • Attach the nozzle's inlet (threaded end) to a compatible fuel hose or pump outlet. Ensure a tight, leak-free connection.
   • Use appropriate thread sealant if necessary to prevent leaks.
   

   Figure 3: Detailed view of the threaded inlet connection, where the fuel hose or pump outlet should be securely attached.

3. Initial Check: Before dispensing, perform a visual inspection for any loose parts or signs of damage.

5. Operating Instructions

Operating the Geko G00950 is straightforward. The integrated digital meter provides real-time flow information.

5.1. Understanding the Digital Display

The LCD display shows various metrics related to the dispensed liquid. Common displays include:

• Current Dispense: Shows the volume of liquid dispensed in the current operation.
• Total Volume: Accumulates the total volume dispensed over time.
• Flow Rate: Indicates the instantaneous rate of liquid flow.

Figure 4: The LCD display showing a current dispense of "10.20 L" and a "RESET TOTAL" option, indicating the accumulated volume.

Figure 5: The LCD display indicating a "FLOW RATE" measurement, providing real-time dispensing speed.

Figure 6: The LCD display showing various measurement units (QTS, PTS, L, GAL) and options for "CAL" (calibration) and "RESET TOTAL", with a finger interacting with the controls.

5.2. Dispensing Liquid

1. Position the Nozzle: Insert the nozzle spout into the receiving container or tank opening.
2. Activate Flow: Squeeze the trigger handle to begin dispensing liquid. The flow rate can often be controlled by the pressure applied to the trigger.
   

   Figure 7: A close-up view of the trigger mechanism on the Geko G00950 fuel nozzle, which controls the flow of liquid.
3. Monitor Display: Observe the LCD display to track the dispensed volume.
4. Stop Flow: Release the trigger to stop the flow of liquid.
5. Reset Current Dispense: After each dispensing operation, press the "RESET" button on the meter to clear the current dispense reading for the next use. Refer to Figure 4 for button location.

5.3. Unit Selection and Calibration

The digital meter may allow for selection of different measurement units (e.g., Liters, Gallons) and calibration for accuracy. Consult the on-screen prompts or specific button combinations (e.g., "CAL" button as seen in Figure 6) for these advanced functions. Typically, holding the "CAL" button or a combination of buttons allows access to these settings.

6. Maintenance

Regular maintenance ensures the longevity and accuracy of your Geko G00950 Fuel Nozzle.

• Cleaning: Wipe the exterior of the nozzle and the digital display with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Storage: Store the nozzle in a clean, dry place away from direct sunlight and extreme temperatures.
• Inspection: Periodically inspect the nozzle for any signs of wear, damage, or leaks, especially around connections and the spout.
• Battery Replacement: If the digital display becomes dim or unresponsive, the internal battery may need replacement. Refer to the meter's specific instructions for battery access, usually involving a small screw-on cover.

7. Troubleshooting

If you encounter issues with your Geko G00950, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, contact customer support.

8. Specifications

9. Warranty and Support

Specific warranty details are not provided in the product information. For warranty claims, technical support, or service inquiries, please contact the retailer or manufacturer directly using the contact information provided at the point of purchase.

Manufacturer: Firma Handlowa GEKO