SafeWaze SW-8008-10-ALU Class A 10' Cable Retractable Lifeline User Manual

1. Introduction

This manual provides essential instructions for the proper use, inspection, and maintenance of the SafeWaze SW-8008-10-ALU Class A 10' Cable Retractable Lifeline. This device is designed as a single-person fall protection component.

The SafeWaze SW-8008-10-ALU features a 10-foot galvanized cable, a mobility-enhancing swivel top, a fall-gate-rated aluminum snap hook, and coated components for demanding work environments. Its design prioritizes durability and portability.

Key Features:

• Designed for single-person fall protection.
• Swivel top for enhanced user mobility.
• Rugged and durable housing.
• Unique braking system to ease shock during a fall event.
• 420 lb. weight capacity.

2. Safety Information

WARNING: Failure to follow all instructions and warnings can result in serious injury or death. This equipment must be used by trained and competent persons only. Consult a qualified person before use if there are any doubts about proper application.

• Always inspect the device before each use.
• Ensure compatibility with all other components of the fall arrest system.
• Do not modify the equipment.
• Ensure adequate fall clearance is maintained below the work area.
• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).

3. Components

The SafeWaze SW-8008-10-ALU retractable lifeline consists of the following primary components:

• Housing: High-strength polymer housing containing the retraction mechanism and braking system.
• Cable: 10-foot galvanized steel cable lifeline.
• Swivel Top: Attachment point for connection to an anchorage connector, allowing for enhanced mobility.
• Aluminum Snap Hook: Connects the lifeline to the user's full-body harness D-ring.
• Energy Absorber: Integrated into the lifeline to reduce forces during a fall.

Image 1: SafeWaze SW-8008-10-ALU Class A 10' Cable Retractable Lifeline. This image shows the complete retractable lifeline unit, including the black housing with the SafeWaze logo, the galvanized cable extending downwards, and the aluminum snap hook at the end. The unit also features a black handle grip and an integrated energy absorber sleeve.

4. Setup and Connection

1. Anchorage Selection: Select an anchorage point capable of supporting 5,000 lbs (22.2 kN) per worker or meeting OSHA 1926.502 requirements for engineered systems. The anchorage should be located directly above the work area to minimize swing fall hazards.
2. Connecting to Anchorage: Attach the swivel top of the retractable lifeline to the selected anchorage connector. Ensure the connection is secure and properly closed.
3. Connecting to Harness: Connect the aluminum snap hook at the end of the lifeline to the dorsal D-ring of a compatible full-body harness. Verify that the snap hook gate is fully closed and locked.
4. Fall Clearance: Before beginning work, calculate and ensure sufficient fall clearance below the work surface. Consider the length of the lifeline, deceleration distance, and any potential sag in the anchorage system.

5. Operating Instructions

Once properly connected, the retractable lifeline will automatically extend and retract as the user moves, providing continuous fall protection. The device is designed to lock instantly upon a sudden pull or fall, arresting the fall within a short distance.

• Move at a normal working speed; rapid movements may cause the unit to lock.
• Always maintain tension on the lifeline to prevent slack that could increase fall distance.
• In the event of a fall, the unit will lock, and the energy absorber will deploy.
• After a fall, the device must be immediately removed from service and inspected by a qualified person.

6. Maintenance and Inspection

Regular inspection and proper maintenance are crucial for the safe operation of the SafeWaze SW-8008-10-ALU retractable lifeline.

6.1 Pre-Use Inspection

Before each use, perform the following checks:

• Inspect the housing for cracks, deformation, or damage.
• Examine the cable for cuts, fraying, kinks, corrosion, or broken strands.
• Check the snap hook for proper operation, ensuring the gate opens freely and closes securely, and that there are no signs of deformation or corrosion.
• Verify the swivel top operates smoothly and is free from damage.
• Ensure the energy absorber is intact and shows no signs of deployment or damage.
• Test the locking mechanism by pulling sharply on the cable. It should lock instantly.

6.2 Periodic Inspection

A qualified person must perform a thorough inspection at least every six months, or more frequently depending on usage and environmental conditions. Maintain detailed inspection records.

6.3 Cleaning and Storage

• Clean the unit with a damp cloth and mild soap. Do not use harsh chemicals.
• Allow the unit to air dry completely before storage.
• Store in a cool, dry place, away from direct sunlight, corrosive chemicals, and extreme temperatures.

7. Troubleshooting

If you encounter any issues with your SafeWaze SW-8008-10-ALU, refer to the following common problems and solutions:

For any issues not listed or if solutions do not resolve the problem, immediately remove the device from service and contact SafeWaze customer support or a qualified service technician.

8. Specifications

9. Warranty and Support

For specific warranty information, please refer to the documentation provided with your product at the time of purchase or visit the official SafeWaze website. For technical support, service, or to report a fall event, please contact SafeWaze directly.

Manufacturer: SafeWaze

Website: www.safewaze.com