Introduction
This manual provides comprehensive instructions for the KeylessOption EZSDEI474V Keyless Entry Remote Starter Car Key Fob. This device is designed as a replacement remote for aftermarket alarm and remote start systems. Please read all instructions carefully before attempting to program or use the remote.
Important: Ensure the FCC ID on your original remote matches EZSDEI474V for compatibility. Programming procedures may vary slightly depending on the specific aftermarket system installed in your vehicle. Refer to your vehicle's owner's manual or the manufacturer's website for additional system-specific details.
Product Overview
The KeylessOption EZSDEI474V remote features a durable design with three primary function buttons and one auxiliary button. It is designed to provide reliable keyless entry and remote start functionality for compatible aftermarket systems.
Figure 1: Front view of the KeylessOption EZSDEI474V remote key fob, showing the Lock, Unlock, Auxiliary, and Panic buttons. The Panic button is yellow with an asterisk symbol.
Package Contents
Verify that your package contains the following items:
- KeylessOption EZSDEI474V Remote Key Fob
- Ring Loop
- CR2032 Lithium Cell Battery (pre-installed)
- Program Guide (this manual)
Figure 2: Image showing the contents of the KeylessOption package: the remote key fob, a metal ring loop, and a CR2032 battery. The battery is typically pre-installed in the remote.
Setup and Programming
The KeylessOption EZSDEI474V remote requires programming to your vehicle's aftermarket alarm/remote start system. This process typically involves accessing a Valet/Programming switch within your vehicle.
Programming Instructions
- Open a vehicle door and ensure the dome light is illuminated.
- Turn the vehicle ignition to the RUN position or start the engine.
- Within 15 seconds, locate and press the Valet/Program push button:
- Press and release 1 time for vehicles equipped with remote start.
- Press and release 7 times for vehicles without remote start.
- While holding the Valet/Program switch, press the Lock button on the new transmitter. A chirp or horn-honk will confirm that the code has been successfully learned.
- Once the code is learned, release the Valet/Program push button.
- Turn the vehicle ignition off and test the remote's functionality.
Figure 3: Visual representation of the programming steps, emphasizing the Valet/Program switch interaction and the remote's Lock button press for code learning.
For additional programming resources, please visit the manufacturer's website or consult your aftermarket system's specific documentation.
Figure 4: This image highlights the DIY self-programming capability and lists compatible aftermarket alarm and remote start systems, including Viper, Python, Avital, Hornet, and Automate, along with various model numbers.
Operating the Remote
Once successfully programmed, your KeylessOption remote will control your vehicle's aftermarket alarm and remote start system. The buttons on the remote perform the following functions:
- Lock Button: Locks vehicle doors and arms the alarm system.
- Unlock Button: Unlocks vehicle doors and disarms the alarm system.
- AUX Button: Activates an auxiliary function, which may vary depending on your aftermarket system's configuration (e.g., trunk release, remote start activation).
- Panic Button (Yellow Asterisk): Activates the vehicle's panic alarm. Press and hold for a few seconds to activate, press again to deactivate.
Refer to your aftermarket system's manual for specific details on how each button interacts with your installed system.
Maintenance
Battery Replacement
The remote uses a CR2032 lithium coin cell battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement.
- Carefully separate the two halves of the remote casing using a small flat-head screwdriver or a coin in the designated notch.
- Remove the old CR2032 battery, noting its orientation (+ side up).
- Insert a new CR2032 battery with the positive (+) side facing up.
- Snap the two halves of the remote casing back together securely.
Dispose of old batteries according to local regulations.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote does not work after programming. | Incorrect programming steps, incompatible FCC ID, dead battery. |
|
| Reduced operating range. | Low battery, environmental interference. |
|
| Vehicle does not respond to remote. | Remote not programmed, vehicle's alarm system issue, remote battery dead. |
|
If you continue to experience issues after following these troubleshooting steps, please contact KeylessOption customer support or a qualified automotive technician.
Specifications
- Model: KPT6058
- FCC ID: EZSDEI474V
- Compatible Systems: Viper, DEI, Automate, Valet, Avital, Clifford, Python Aftermarket Alarm/Remote Start Systems (with matching FCC ID)
- Battery Type: CR2032 Lithium Coin Cell
- Dimensions: Approximately 2 x 0.75 x 4 inches
- Weight: Approximately 0.317 ounces
Warranty and Support
KeylessOption products are designed for reliability and performance. For specific warranty information, please refer to the product packaging or the official KeylessOption website. For technical support or further assistance, please visit the KeylessOption Store on Amazon or contact their customer service directly.
Note: This is a replacement part designed to match the original in form and function. Ensure compatibility before purchase.
Video Resources
The following video provides an overview of KeylessOption products and may offer additional context for your remote key fob.
Video 1: An introductory video from KeylessOption, showcasing their range of key fob remotes for Viper and other compatible systems. This video provides a general overview of the brand and product type.