Introduction
This manual provides essential instructions for the safe assembly, operation, and maintenance of your Intex Prism Frame Oval Pool Set, Model 26796. Please read all instructions carefully before installation and retain this manual for future reference. Proper installation and adherence to safety guidelines are crucial for a safe and enjoyable swimming experience.
Important Safety Information
WARNING: The use of a swimming pool requires adherence to the safety guidelines described in the operating and maintenance instructions. To prevent drowning or other serious injuries, pay particular attention to the possibility of unexpected access to the pool by children under 5 years of age. Secure access to the pool and keep children under constant adult supervision during bath time. Please refer to local building regulations for all installation requirements. Prevent unsupervised access. Intex strongly recommends enclosing pools with a corresponding protective fence. Please contact your local building department for more information on applicable permit requirements.
- Never leave children unattended in or around the pool.
- Always ensure adult supervision when the pool is in use.
- Keep all electrical devices away from the pool.
- Do not dive or jump into the pool.
- Ensure the pool is installed on a level, stable surface.
Package Contents
Verify that all components listed below are present before beginning assembly. If any parts are missing or damaged, do not proceed with assembly and contact Intex customer service.
- Prism Frame Oval Pool Liner
- Steel Frame Components (horizontal beams, vertical legs, T-joints)
- Filter Pump with Hydro Aeration Technology (UK 3-pin plug)
- Safety Ladder
- Ground Cloth
- Pool Cover
- Hoses and Clamps for Filter Pump
- Instruction Manual (this document)
Image: Assembled Intex Prism Frame Oval Pool Set with water.
Image: Included safety ladder for pool access.
Image: Pool cover for protection when not in use.
Image: Ground cloth to protect the pool liner.
Setup Instructions
- Site Preparation: Choose a firm, level area free of sharp objects, debris, and overhead power lines. Ensure the ground can support the weight of the filled pool (approximately 13,365 liters or 3,531 gallons).
- Ground Cloth Placement: Spread the ground cloth evenly on the prepared site. This protects the pool liner from punctures.
- Liner Unfolding: Carefully unfold the pool liner over the ground cloth. Position the drain plug away from the main traffic area.
- Frame Assembly: Assemble the steel frame components according to the diagrams in your separate assembly guide. Connect the horizontal beams to the T-joints and then insert the vertical legs. Ensure all connections are secure.
- Filling the Pool: Begin filling the pool with water. As the water level rises, smooth out any wrinkles in the bottom of the liner. Stop filling when the water reaches the fill line indicated on the liner, or approximately 90% capacity.
- Filter Pump Installation: Connect the filter pump to the pool's inlet and outlet fittings using the provided hoses and clamps. Ensure all connections are tight to prevent leaks. Position the pump on a stable surface at least 2 meters (6.5 feet) from the pool.
- Ladder Assembly: Assemble the safety ladder according to its separate instructions. Place the ladder on a firm, level surface outside the pool.
Image: Example of a T-joint component used in the pool frame assembly.
Image: A person demonstrating the setup of the filter pump next to the pool.
Image: Detailed view of the Intex filter pump unit.
Operation
Filter Pump Operation
The included filter pump is designed to circulate and filter the pool water, helping to keep it clean. The pump features Hydro Aeration Technology for improved water circulation and filtration.
- Ensure the pump is properly connected and the power cord is plugged into a grounded outlet.
- Run the filter pump for at least 4-6 hours daily to maintain water clarity.
- Refer to the separate filter pump manual for detailed operating instructions, including backwashing and filter cartridge replacement.
Image: Close-up of the Hydro Aeration Technology outlet, which enhances water circulation and filtration.
Maintenance
Water Chemistry
Regularly test and adjust pool water chemistry to ensure a safe and sanitary swimming environment. Maintain appropriate levels for pH, chlorine, and alkalinity as recommended by local health authorities or pool chemical manufacturers.
Cleaning
- Skim debris from the water surface daily using a pool skimmer.
- Brush the pool walls and bottom weekly to prevent algae growth.
- Vacuum the pool bottom as needed to remove settled debris.
- Clean or replace the filter cartridge in the pump regularly (typically every 2 weeks, or more often with heavy use).
Pool Cover Use
Use the included pool cover when the pool is not in use to prevent debris from entering the water and to reduce evaporation.
Image: Diagram showing the pool cover installed on the Intex Prism Frame Oval Pool.
Winterization
Before freezing temperatures arrive, the pool must be properly drained, cleaned, and stored. Refer to the separate winterization guide for detailed instructions.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water is cloudy | Insufficient filtration; improper chemical balance; heavy use. | Run filter pump longer; clean/replace filter cartridge; test and adjust water chemistry; shock treat pool. |
| Pump not running | No power; clogged impeller; air lock. | Check power connection and circuit breaker; unplug and inspect impeller for debris; prime the pump according to its manual. |
| Water leaking from connections | Loose clamps; worn O-rings/gaskets. | Tighten hose clamps; inspect and replace O-rings/gaskets if damaged. |
| Algae growth | Low chlorine; high pH; poor circulation. | Shock treat with algaecide; adjust pH; ensure adequate pump run time. |
Specifications
- Model Number: 26796
- Dimensions (L x W x H): 5.03 m x 2.74 m x 1.22 m (16 ft 6 in x 9 ft x 48 in)
- Water Capacity (90%): 13,365 liters (3,531 gallons)
- Shape: Oval
- Material: Alloy Steel Frame, 3-Ply Durable Liner
- Color: Grey
- Included Components: Pool Liner, Steel Frame, Filter Pump, Safety Ladder, Ground Cloth, Pool Cover
- Special Features: Hydro Aeration Technology in Filter Pump
- Assembly Required: Yes
- Usage: Outdoor
- Item Weight: 112.1 kg (247.1 lbs)
Image: Diagram illustrating the dimensions of the Intex Prism Frame Oval Pool.