UpStart Components S60 Semi Chisel Chainsaw Chain 18-Inch User Manual

1. Introduction

This manual provides essential information for the safe and effective use, installation, and maintenance of your UpStart Components S60 Semi Chisel Chainsaw Chain. Please read this manual thoroughly before installation and operation to ensure proper function and safety.

The UpStart Components S60 Semi Chisel Chainsaw Chain is an 18-inch replacement chain designed for various chainsaw models, featuring a 3/8" pitch, 0.050" gauge, and 60 drive links. It is engineered for smooth cuts, precision, balance, and durability.

2. Safety Information

WARNING: Chainsaws are dangerous tools. Always wear appropriate personal protective equipment (PPE) including safety glasses, hearing protection, gloves, and protective legwear when handling or operating a chainsaw. Refer to your chainsaw's original instruction manual for complete safety guidelines.

• Always ensure the chainsaw is turned off and the spark plug cap is disconnected (for gasoline models) or the battery is removed (for electric models) before handling the chain.
• Inspect the chain for damage before each use. Replace dull or damaged chains immediately to prevent injury and ensure efficient cutting.
• Maintain proper chain tension. A loose chain can derail, causing injury. A too-tight chain can cause excessive wear and damage to the chainsaw.
• Keep hands and body clear of the chain when the chainsaw is running.
• Store chains safely to prevent accidental contact.

3. Compatibility

This 18-inch S60 Semi Chisel Chainsaw Chain is compatible with a range of chainsaw models. It is crucial to verify your chainsaw's specific requirements for pitch, gauge, and drive links before purchasing and installing any replacement chain, as the same saw model can have different bar lengths and chain specifications.

Chain Specifications:

• Length: 18 inches
• Pitch: 3/8"
• Gauge: 0.050"
• Drive Links: 60

Known compatible models include, but are not limited to:

• Craftsman: 41554, 41556, 41558
• Mastercraft: 54-5720 (pre Apr 99), 54-5721 (pre Apr 99), 54-5724 (pre Apr 99), 54-5722 (pre Apr 99)
• McCulloch: Electramac 14A/S, 14AE, 14E, 2010, 2116, EM14E, EM16E, Mac 110, 115, 120, 130, 140, 160S, 3200, 3210, 3214, 3216, 3514, 3516, 3518, 3816, 3818AV, 435, 440, MacCat Super 6AV, 18AV, 165, 310, 320, 330, 340, 510, 515, Mini Mac MS1436, Titan 35, 40, 1839NAV, Eager Beaver 2010, 2016, Electramac 12A/S, 12AE, 12E, 2014, 2016, 2310, 35A/S, Mac 3205, 3212, 400, 430, 445, MacCat 38, MCC1514, MS1639NAVCC, MS1839, Power Mac 310, 320, 330, POWER MAC 6, PowerMac 145-14, 255-16, Silver Eagle 2116AVS, 2316, 2318AVS, Super 2318AV, Wildcat/MacCat, Electramac 10E, Eager Beaver 2014.

Note: This is a replacement part and not an OEM product. Compatibility is listed for illustrative purposes.

4. Setup (Chain Installation)

Follow these general steps to install your new chainsaw chain. Always refer to your chainsaw's specific instruction manual for detailed, model-specific installation procedures.

1. Ensure Safety: Turn off the chainsaw, disconnect the spark plug cap (gas models) or remove the battery (electric models). Engage the chain brake.
2. Remove Bar Cover: Loosen and remove the nuts holding the clutch cover/side plate in place. Remove the cover.
3. Remove Old Chain: Loosen the bar tensioning screw. Carefully remove the guide bar and the old chain.
4. Clean Components: Clean any sawdust or debris from the guide bar groove, sprocket, and clutch area.
5. Install New Chain: Place the new UpStart Components S60 chain onto the sprocket, ensuring the cutting edges face the correct direction (usually forward on the top of the bar). Fit the chain into the groove of the guide bar.
6. Reattach Bar Cover: Slide the guide bar back into position, ensuring the chain drive links are properly seated in the sprocket and the bar's studs align with the mounting holes. Replace the clutch cover/side plate and hand-tighten the nuts.
7. Adjust Chain Tension: Adjust the chain tensioning screw until the chain is snug against the guide bar, but can still be pulled freely by hand. The chain should not sag on the underside of the bar. A good test is to lift the chain drive links out of the bar groove; they should just barely clear the bottom of the groove.
8. Tighten Nuts: While holding the tip of the guide bar up, fully tighten the clutch cover/side plate nuts.
9. Final Check: Reconnect the spark plug cap or reinsert the battery. Briefly run the chainsaw at low speed to allow the chain to seat, then re-check and adjust tension if necessary.

Image 1: UpStart Components S60 Semi Chisel Chainsaw Chain. This image shows the replacement chain coiled, highlighting its semi-chisel tooth design and overall construction. It is an 18-inch chain with 3/8" pitch, 0.050" gauge, and 60 drive links.

5. Operating (Chain Usage)

Once the chain is correctly installed and tensioned, operate your chainsaw according to its manufacturer's instructions. The UpStart Components S60 chain is designed for efficient cutting performance.

• Lubrication: Ensure your chainsaw's automatic oiler is functioning correctly and the oil reservoir is filled with appropriate bar and chain oil. Proper lubrication is critical for chain longevity and performance.
• Cutting Technique: Use proper cutting techniques as outlined in your chainsaw's manual. Avoid forcing the chain through wood; let the chain do the work.
• Avoid Obstacles: Do not cut into dirt, rocks, or metal, as this will dull or damage the chain quickly.
• Monitor Performance: If the chain starts to cut slowly, pull to one side, or produce fine dust instead of chips, it likely needs sharpening or replacement.

6. Maintenance

Regular maintenance extends the life of your chain and ensures safe operation.

• Sharpening: Sharpen the chain regularly. A sharp chain cuts efficiently and reduces strain on the chainsaw. Use a round file of the correct diameter (typically 5/32" for 3/8" low profile chains, but verify for your specific chain) and a flat file for depth gauges. Maintain consistent angles for all cutters.
• Cleaning: After each use, clean sawdust and debris from the chain, guide bar groove, and sprocket.
• Tension Check: Re-check chain tension frequently, especially during the first hour of use with a new chain, and before each subsequent use. Chains can stretch slightly during initial use.
• Storage: When not in use, clean and lightly oil the chain before storing it in a dry place to prevent rust.
• Replacement: Replace the chain when it becomes too dull to sharpen effectively, or if it shows signs of damage such as cracks, bent links, or excessive wear.

7. Troubleshooting

8. Specifications

• Brand: UpStart Components
• Model: S60 (CSC-S60)
• Chain Type: Semi-Chisel
• Chain Length: 18 Inches
• Pitch: 3/8"
• Gauge: 0.050"
• Drive Links: 60
• UPC: 628586038219

9. Warranty and Support

Any warranties for this UpStart Components S60 Semi Chisel Chainsaw Chain are offered solely by UpStart Components. This product is not affiliated with any OEM brands and is not covered under any warranties offered by the original manufacturers of compatible chainsaws.

For warranty claims, technical support, or further assistance, please contact UpStart Components directly through their official customer service channels. Refer to your purchase documentation for specific contact information.