ECONTROLLY EN-31201A
ECONTROLLY EN-31201A Replacement Remote Control User Manual
Model: EN-31201A
Introduction
This manual provides instructions for the ECONTROLLY EN-31201A replacement remote control. This remote is designed to be compatible with various Hisense TV models, offering a direct replacement for your original remote without requiring complex programming.
Compatibility
The EN-31201A remote control is compatible with a wide range of Hisense TV models. Please verify your TV model against the list below:
- LTDN46K20US, LTD24V86US, LTDN42K20US, LTDN42V77US
- LTDN39V77US, LEDN32K15US, LHD32K20AUS, LHD32K26US, LHD37V87US, LHDN32V66AUS, LTDN23K15US, LTDN24K16US, LTDN24K20US, LTDN24V87US
- LTDN39V78US, LTDN40K26US, LTDN40V87US, LTDN42K26US, LTDN55V89GUS, LTDN24V86US
- LTDN46V86US, F24V77C, F24V86C, F46V89C, F55V89C, F39V77C, F40V87C, F42K26, F42V77C
- F46K20E, F46V86C, F46V89C, F55V89C, H32K26E, H32V77C
Setup
Battery Installation
The remote control requires two (2) AAA batteries for operation. Batteries are typically not included and must be purchased separately.
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards to open it.
- Insert two new AAA alkaline batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Replace the battery compartment cover by sliding it upwards until it clicks into place.
The remote is ready for use immediately after battery installation; no programming is required.
Figure 1: Battery compartment with cover removed. Insert two AAA batteries as shown.
Operating Instructions
This section details the functions of the buttons on your ECONTROLLY EN-31201A remote control.
Figure 2: Front view of the EN-31201A remote control.
Button Functions
| Button | Function |
|---|---|
| POWER | Turns the TV on or off. |
| INPUT | Selects the input source (e.g., HDMI, AV, Component). |
| TV | Switches to TV mode. |
| AV / COMP / HDMI / VGA | Direct selection of specific input sources. |
| ASPECT | Adjusts the screen aspect ratio. |
| GUIDE | Displays the electronic program guide. |
| PICTURE | Accesses picture settings. |
| SOUND | Accesses sound settings. |
| DISPLAY | Shows on-screen display information. |
| MUTE | Mutes or unmutes the TV sound. |
| Volume Up/Down | Adjusts the volume level. |
| Channel Up/Down | Changes TV channels. |
| MENU | Opens the TV's main menu. |
| EXIT | Exits the current menu or function. |
| Navigation Arrows (Up/Down/Left/Right) | Navigates through menus and options. |
| ENTER | Confirms selections in menus. |
| Number Buttons (0-9) | Direct channel selection. |
| LAST | Returns to the previously viewed channel. |
| CCD | Activates Closed Captioning. |
| MTS/SAP | Selects Multi-channel Television Sound/Secondary Audio Program. |
| TIME | Accesses time-related functions or display. |
| SLEEP | Sets the sleep timer. |
Maintenance
- Keep the remote control clean by wiping it with a soft, dry cloth.
- Avoid exposing the remote to extreme temperatures, humidity, or direct sunlight.
- Do not drop the remote control or subject it to strong impacts.
- If the remote will not be used for an extended period, remove the batteries to prevent leakage.
Troubleshooting
Remote Control Not Responding
- Check Batteries: Ensure batteries are inserted correctly with the correct polarity (+/-). Replace old batteries with new AAA alkaline batteries.
- Line of Sight: Make sure there is a clear line of sight between the remote control and the TV's infrared sensor. Obstructions can block the signal.
- Distance: Ensure you are within the effective operating range (approximately 10 meters or 33 feet).
- TV Sensor: Verify that the TV's remote sensor is not blocked or dirty.
Intermittent Operation
- Weak Batteries: Replace batteries even if they seem to be partially working.
- Interference: Other electronic devices or strong light sources might interfere with the remote's signal. Try using the remote in a different environment.
Specifications
| Feature | Detail |
|---|---|
| Model | EN-31201A |
| Brand | ECONTROLLY |
| Material | ABS Material |
| Power Source | 2 x AAA Batteries (not included) |
| Transmitting Distance | Approximately 10 meters (33 feet) |
| Product Dimensions | 7 x 2 x 0.65 inches |
| Item Weight | 2 ounces |
| Color | Black |
| Compatible Devices | Television |
Warranty Information
This product is a replacement remote control. Please refer to the original product's documentation or the seller for specific warranty details, if any. General return policies may apply as per the point of purchase.
Support
For further assistance or inquiries regarding the ECONTROLLY EN-31201A remote control, please contact your retailer or the ECONTROLLY customer support channels available at the time of purchase.
Related documentsEN-31201A
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.