Product Overview
The Jebao 2018 new DCP pumps offer enhanced performance and precise flow control for your aquarium's reactors, sump, or closed loop system. Designed for efficiency and quiet operation, this pump provides reliable water circulation for aquatic environments.
Key Features
- Latest DCP model with improved performance over the DCT series.
- High-performance motor with innovative electronics, offering up to 50% energy savings compared to older models.
- Constructed without copper components, ensuring safety for your aquatic tank. Designed for internal use only.
- Features super quiet operation for a peaceful aquatic environment.
- Includes a memory function to recall settings after a power supply interruption.
- Power: 28-watt, 110-120V 60Hz; Max Flow: 925 GPH; Max Head: 11.5 ft.
- Compact dimensions: 6" x 3" x 4".
What's Included
Your Jebao DCP Sine Wave Water Return Pump package includes the following components:
- DCP pump unit
- AC adapter
- Controller
- Various fittings and O-rings for installation
Image: All components included with the Jebao DCP-3500 Sine Wave Water Return Pump, including the pump unit, controller, power adapter, and various connection fittings.
Setup Guide
1. Placement
Position the pump in your sump or desired location within the aquarium system. Ensure it is placed on a stable, level surface. The pump is designed for internal use only and must be fully submerged during operation.
2. Connections
- Attach the appropriate fittings to the pump's inlet and outlet ports. Ensure all connections are secure and watertight to prevent leaks.
- Connect the pump to the controller cable, ensuring the connection is firm.
- Connect the AC adapter to the controller, and then plug the AC adapter into a grounded electrical outlet.
Image: A detailed view of the Jebao DCP pump unit, showing its compact design and the protective intake screen.
3. Priming (if applicable)
For optimal performance, ensure the pump is fully submerged and free of air pockets before powering on. If necessary, gently rock the pump to release any trapped air.
Operating Instructions
1. Powering On
Once all connections are secure and the pump is submerged, plug the AC adapter into a power source. The pump will initiate operation.
2. Controller Functions
The DCP controller allows for precise adjustment of the pump's flow rate and access to special modes:
- Flow Control: Use the UP and DOWN buttons on the controller to increase or decrease the water flow rate to your desired level. The digital display will show the current power setting.
- Feed Mode: Press the "Feed" button to activate a 10-minute pause in pump operation, allowing for feeding without water disturbance. The pump will automatically resume after 10 minutes.
- Motor Protection: The controller features a motor protection function that will shut down the pump if the rotor becomes blocked, preventing damage.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your Jebao DCP pump.
1. Regular Cleaning
- Disconnect the pump from power before performing any maintenance.
- Periodically remove the pump from the sump and rinse it thoroughly with clean water to remove any accumulated debris or algae.
- Clean the intake screen regularly to prevent blockages and maintain optimal flow.
2. Impeller Cleaning
- Carefully disassemble the pump housing to access the impeller.
- Clean the impeller and its chamber using a soft brush and clean water. Remove any calcium buildup or foreign objects that may impede its rotation.
- Inspect the O-rings for wear and tear. Replace if necessary to ensure a watertight seal.
- Reassemble the pump, ensuring all parts are correctly seated.
Troubleshooting
If you encounter issues with your Jebao DCP pump, refer to the table below for common problems and solutions. For more detailed troubleshooting, consult the full user manual.
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump not running | No power, blocked impeller, faulty controller/adapter | Check power connection, clean impeller, test controller/adapter |
| Reduced flow | Clogged intake, dirty impeller, air in pump | Clean intake/impeller, re-prime pump to remove air |
| Unusual noise | Debris in impeller, pump not fully submerged, vibration | Clean impeller, ensure full submersion, check for stable placement |
| Controller display error | Loose connection, internal fault | Check cable connections, power cycle the unit. If persistent, contact support. |
Technical Specifications
| Specification | Value |
|---|---|
| Model | DCP-3500 |
| Power | 28 Watts |
| Voltage | 110-120 Volts |
| Frequency | 60 Hz |
| Maximum Flow Rate | 925 Gallons Per Hour (GPH) / 3500 Liters Per Hour (LPH) |
| Maximum Head Lift | 11.5 Feet / 3.5 Meters |
| Product Dimensions (L x W x H) | 6" x 3" x 4" (approximate) |
| Item Weight | 3.77 Pounds |
| Material | Copper-free construction |
| Usage Environment | Indoor, Submersible |
Warranty Information
The Jebao DCP Sine Wave Water Return Pump (DCP-3500) comes with a 180-day warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by misuse, improper installation, unauthorized modifications, or normal wear and tear.
Customer Support
For further assistance, detailed instructions, or technical support, please refer to the official user manual or contact Jebao customer service.
You can download the complete User Manual (PDF) here.
For specific inquiries or warranty claims, please visit the official Jebao website or contact their support channels as listed in the full manual or product packaging.
