Product Overview
This manual provides instructions for the uxcell 20x7x6mm carbon brushes, designed as replacement parts for various electric motors found in power tools such as treadmills, wood trimmers, and laminate trimmers.
Carbon brushes are essential components in many electric motors, facilitating the transfer of electrical current to the motor's rotating parts. They are subject to wear and tear during normal operation and require periodic replacement to maintain motor performance and prevent damage to the motor's commutator.
Installation Guide
Safety Precautions
- Always disconnect the power tool from its power source before attempting any maintenance or replacement.
- Wear appropriate personal protective equipment (PPE), such as safety glasses.
- Ensure the work area is well-lit and clear of obstructions.
Identifying Worn Brushes
Worn carbon brushes are a common cause of intermittent motor operation, reduced power, or complete motor failure. Symptoms may include excessive sparking, unusual noises, or the motor failing to start. Replacing worn brushes can restore motor function and electric braking.
Replacement Procedure
- Locate the Brush Holders: On most electric motors, carbon brushes are housed in accessible compartments, often secured by screws or clips. Refer to your specific power tool's manual for exact locations.
- Remove Old Brushes: Carefully remove the old carbon brushes. Note their orientation and how they are connected to the motor's internal wiring.
- Inspect and Clean: Inspect the commutator (the part of the motor that the brushes contact) for any damage or excessive carbon buildup. Clean if necessary.
- Insert New Brushes: Insert the new uxcell carbon brushes (20mm x 7mm x 6mm) into the brush holders. Ensure they slide freely and make proper contact with the commutator. The spring should provide adequate pressure.
- Secure Brush Holders: Re-secure the brush holders.
- Test Operation: Reconnect the power tool to its power source and perform a brief test run to ensure proper function. Observe for any unusual sparking or sounds.

This image illustrates the precise measurements of the carbon brush, indicating a length of 20mm (0.79 inches), a width of 7mm (0.28 inches), a height of 6mm (0.24 inches), and a spring length of 25mm (0.98 inches). These dimensions are crucial for ensuring compatibility with your electric motor.

This image displays a single uxcell carbon brush, highlighting its carbon block, coiled spring, and the metal terminal designed for electrical connection. The spring ensures constant contact between the brush and the motor's commutator.

This image presents two uxcell carbon brushes, providing a visual representation of the product included in the 10-piece package. Each brush consists of a carbon block, a spring, and a metal connector.
Operation After Replacement
After successful installation, the electric motor should operate smoothly with restored power and consistent performance. It is normal for new carbon brushes to produce a small amount of sparking during the initial break-in period. If excessive sparking or unusual noises persist, refer to the troubleshooting section.
Maintenance and Care
Regularly inspect carbon brushes for wear, especially in tools used frequently. The lifespan of carbon brushes varies depending on motor usage and operating conditions. Replace brushes when they are significantly worn down to prevent damage to the motor's commutator and ensure optimal motor performance.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not starting or intermittent operation | Worn or improperly installed carbon brushes | Ensure brushes are correctly seated and making full contact. Replace if worn. |
| Excessive sparking at brushes | New brushes breaking in, or commutator issues | Initial sparking is normal. If persistent, check commutator for damage or dirt. Ensure brushes are the correct size. |
| Reduced motor power | Worn brushes or other motor component failure | Replace brushes. If problem persists, consult a qualified technician for further motor inspection. |
Product Specifications
- Brand: uxcell
- Model Number: a18050500ux0020
- Carbon Brush Dimensions (L x W x H): 20mm x 7mm x 6mm (0.79" x 0.28" x 0.24")
- Spring Length: Approximately 25mm (0.98")
- Quantity: 10 Pieces per package
- Material: Carbon, Metal
- Weight: 0.04 kg (for the package)
Warranty and Support
For product support, technical assistance, or warranty inquiries, please contact uxcell directly through their official channels. Information may be available on the uxcell Brand Store.