Introduction
This manual provides essential information for the safe and efficient operation of your TUNÇMATİK Newtech Pro X9 10 KVA Uninterruptible Power Supply (UPS). Please read this manual thoroughly before installation and operation. Keep this manual in a safe place for future reference.
The Newtech Pro X9 10 KVA is an online UPS designed to provide clean, stable, and reliable power to critical equipment, protecting against power outages, surges, and fluctuations. It features an LCD screen for easy monitoring and control.
Safety Instructions
Observe the following safety precautions to prevent injury and damage to the UPS or connected equipment:
- Do not open the UPS casing. There are no user-serviceable parts inside. Refer servicing to qualified personnel.
- Ensure the UPS is connected to a grounded power outlet.
- Do not block ventilation openings. Maintain adequate clearance around the UPS for proper airflow.
- Avoid installing the UPS in areas with excessive dust, humidity, or extreme temperatures.
- Disconnect the UPS from the power source before performing any maintenance or cleaning.
- The UPS contains internal batteries. Do not dispose of batteries in a fire, as they may explode.
Product Overview
Figure 1: Front view of the TUNÇMATİK Newtech Pro X9 10 KVA UPS, showing the LCD display and control panel.
The TUNÇMATİK Newtech Pro X9 10 KVA UPS features a robust design for critical power protection. Key components include:
- LCD Display: Provides real-time status, input/output voltage, battery level, and alarm information.
- Control Buttons: For navigating menus and configuring settings.
- Input/Output Terminals: For connecting to the main power supply and protected equipment.
- Ventilation Grilles: Essential for heat dissipation.
Setup
1. Unpacking and Inspection
- Carefully unpack the UPS and its accessories.
- Inspect the unit for any physical damage that may have occurred during transit. If damage is found, contact your dealer immediately.
- Verify that all standard accessories are present: UPS unit, user manual, and any included cables.
2. Placement
- Place the UPS in a clean, dry, and well-ventilated area.
- Ensure the ambient temperature is between 0°C and 40°C (32°F and 104°F).
- Avoid direct sunlight and heat sources.
- Maintain at least 20 cm (8 inches) of clearance around the front, back, and sides of the UPS for proper ventilation.
3. Electrical Connection
- Ensure the main power switch is in the OFF position.
- Connect the UPS input power cable to a grounded electrical outlet.
- Connect your critical equipment to the UPS output terminals. Ensure the total load does not exceed the UPS's rated capacity (10 KVA).
- For models with external battery packs (if applicable), connect them according to the separate battery pack manual.
Operating Instructions
1. Initial Startup
- After connecting all cables, turn on the main power switch.
- Press and hold the power button on the front panel for approximately 3 seconds until the UPS powers on.
- The LCD display will illuminate and show the startup sequence.
- Allow the UPS to perform its self-test. Once complete, it will enter normal operation mode, providing power to connected devices.
2. LCD Display and Control Panel
The LCD display provides critical information about the UPS status. Use the control buttons to navigate through menus and view parameters such as:
- Input/Output Voltage and Frequency
- Battery Charge Level and Remaining Runtime
- Load Percentage
- Operating Mode (Online, Battery, Bypass)
- Alarm and Event Logs
3. Shutdown Procedure
- Ensure all connected equipment is safely shut down.
- Press and hold the power button on the front panel for approximately 3 seconds until the UPS powers off.
- Disconnect the UPS from the main power supply if it will not be used for an extended period.
Maintenance
1. Battery Care
- The UPS batteries are designed for a specific lifespan. Regular self-tests help monitor battery health.
- Avoid frequent deep discharges, which can shorten battery life.
- If the UPS is stored for an extended period, recharge the batteries every 3-6 months to prevent permanent damage.
- Battery replacement should only be performed by qualified service personnel.
2. Cleaning
- Ensure the UPS is turned off and disconnected from the power source before cleaning.
- Use a soft, dry cloth to wipe the exterior of the UPS.
- Do not use liquid cleaners or solvents, as they may damage the casing or internal components.
- Periodically clean ventilation grilles to ensure unobstructed airflow.
Troubleshooting
This section provides solutions to common issues. If the problem persists, contact technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| UPS does not turn on. | No input power; Battery deeply discharged; Power button not held long enough. | Check power cord connection and wall outlet; Allow UPS to charge for several hours; Press and hold power button for 3 seconds. |
| UPS beeps continuously. | On battery power; Overload; Battery fault. | Check input power; Reduce connected load; Contact service for battery check. |
| Connected equipment not receiving power. | UPS in bypass mode; Output circuit breaker tripped; UPS fault. | Check LCD for operating mode; Reset output circuit breaker; Contact technical support. |
Specifications
| Feature | Description |
|---|---|
| Model | Newtech Pro X9 10 KVA |
| Capacity | 10 KVA |
| Topology | Online (Double Conversion) |
| Input Phase | 1-Phase |
| Output Phase | 1-Phase |
| Battery Type | Sealed Lead-Acid (20 * 12V 9AH) |
| Runtime (Full Load) | 5-15 minutes (depending on load) |
| Display | LCD Screen |
| Dimensions (Approx.) | Refer to product documentation for exact dimensions. |
| Weight (Approx.) | Refer to product documentation for exact weight. |
Warranty and Support
TUNÇMATİK products are backed by a limited warranty. Please refer to the warranty card included with your product or visit the official TUNÇMATİK website for detailed warranty terms and conditions.
For technical support, service, or inquiries, please contact your local TUNÇMATİK dealer or authorized service center. When contacting support, please have your product model number (Newtech Pro X9 10 KVA) and serial number ready.
Manufacturer: TUNÇMATİK
