Pxwaxpy 6000mAh Battery Case for iPhone 6/6s/7/8/SE (2020/2022)

1. Introduction

This manual provides instructions for the Pxwaxpy 6000mAh Rechargeable Battery Case, designed to extend the battery life and provide protection for your compatible iPhone model. Please read this manual thoroughly before use to ensure proper operation and longevity of your device.

1.1 Package Contents

• 1 x Pxwaxpy 6000mAh Battery Case (Model HI850B2)
• 1 x User Manual

Note: A charging cable is not included in the package. Please use your original iPhone charging cable.

1.2 Compatibility

This battery case is specifically designed for 4.7-inch iPhone models:

• iPhone 6
• iPhone 6s
• iPhone 7
• iPhone 8
• iPhone SE (2nd Gen 2020)
• iPhone SE (3rd Gen 2022)

Important: This case is NOT compatible with iPhone 6 Plus, 6s Plus, 7 Plus, 8 Plus (5.5 inch) or any other phone models.

Figure 1.1: Compatible iPhone Models (4.7-inch)

2. Safety Information

Please observe the following safety guidelines to prevent damage to the product or injury.

• Do not crush, puncture, incinerate, or short-circuit the battery case.
• Do not disassemble the device.
• Store in a dry location only. This charger case is not waterproof.
• Avoid exposing the case to extreme temperatures.
• Turn off the battery case when not in use to conserve power and prevent accidental activation.

2.1 Disassembly Warning

Figure 2.1: Internal Disassembly Warning

When removing your iPhone from the battery case, avoid tilting the phone at a sharp angle. Doing so may damage the connector of the battery case.

3. Product Overview

The Pxwaxpy 6000mAh Battery Case is designed to provide extended power and comprehensive protection for your iPhone.

3.1 Key Features

• High Capacity Battery: Built-in 6000mAh battery extends iPhone usage time significantly (e.g., up to 17 hours talk time, 60 hours music time, 13 hours video time).
• Sync & Charging: Supports simultaneous data syncing to a computer and charging of your iPhone without removing the case.
• 360° Protection: Provides full protection against scratches, drops, and daily wear and tear.
• Smart Charging: Internal chips protect your iPhone from overheating, short-circuiting, and overcharging, automatically stopping charging when the iPhone reaches 100%.
• LED Power Indicators: Four LED lights display the remaining battery level of the case.

Figure 3.1: 360° Protective Design

Figure 3.2: Extended Battery Life

4. Setup

4.1 Installing Your iPhone

1. Gently slide your iPhone into the battery case, ensuring the Lightning connector on the case aligns with your iPhone's charging port.
2. Push the iPhone down firmly until it is securely seated and the top cap of the case covers the phone.

Figure 4.1: iPhone Installation

4.2 Initial Charging of the Battery Case

Before first use, fully charge the battery case. Connect your original iPhone Lightning cable to the charging port at the bottom of the battery case, then connect the other end to a power source (e.g., wall adapter, computer USB port).

5. Operating Instructions

5.1 Charging Your iPhone

To begin charging your iPhone using the battery case:

1. Ensure your iPhone is correctly installed in the battery case.
2. Press and hold the ON/OFF button located at the bottom of the charging case for 3 seconds.
3. The LED indicators will light up, and your iPhone will begin charging.

5.2 Charging the Battery Case and iPhone Simultaneously

You can charge both the battery case and your iPhone at the same time:

1. Connect your original iPhone Lightning cable to the charging port of the battery case.
2. Connect the other end to a power source.
3. The battery case will prioritize charging your iPhone first, then recharge itself.

5.3 Data Sync Function

The battery case supports data synchronization with your computer:

1. Connect your iPhone (inside the battery case) to your computer using your original Lightning cable.
2. Your iPhone will sync data with your computer as if it were directly connected, while also charging.

Figure 5.1: Charge & Sync Functionality

5.4 LED Power Indicators

The four LED lights on the back of the battery case indicate the remaining power level:

• 4 LEDs: 75% - 100% charged
• 3 LEDs: 50% - 75% charged
• 2 LEDs: 25% - 50% charged
• 1 LED: 0% - 25% charged

Figure 5.2: LED Power Indicators

5.5 Headphone Compatibility

• For iPhone 6/6s: Compatible with traditional 3.5mm Lightning headphones or wireless Bluetooth headphones.
• For iPhone 7/8/SE (2020/2022): Only works with Apple AirPods or other wireless Bluetooth headphones. Not compatible with wired Lightning headphones.

6. Maintenance

To ensure the longevity and optimal performance of your Pxwaxpy battery case, follow these maintenance guidelines:

• Cleaning: Wipe the case with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
• Storage: Store the case in a cool, dry place away from direct sunlight and extreme temperatures.
• Water Exposure: The case is not waterproof. Avoid exposure to water or other liquids.
• Usage: Turn off the battery case when not actively charging your iPhone to prevent unnecessary power drain.

7. Troubleshooting

If you encounter issues with your Pxwaxpy battery case, refer to the following common problems and solutions:

7.1 Case Not Charging iPhone

• Check Installation: Ensure your iPhone is fully and correctly seated in the battery case, with the Lightning connector properly engaged.
• Activate Charging: Press and hold the ON/OFF button on the case for 3 seconds to initiate charging. Check if the LED indicators light up.
• Case Battery Level: Verify the battery case has sufficient charge by checking the LED indicators. Recharge the case if necessary.
• Clean Ports: Inspect both the iPhone's charging port and the case's Lightning connector for any debris or lint that might obstruct the connection.

7.2 Battery Case Not Recharging

• Cable Check: Ensure you are using an original Apple Lightning cable and that it is securely connected to both the case and the power adapter.
• Power Source: Try a different power adapter or USB port to rule out issues with the power source.
• Connection Integrity: Ensure the charging cable remains firmly connected to the case's port. Loose connections can prevent charging.

7.3 Overheating During Use/Charging

• Disconnect: If the case or iPhone feels excessively hot, immediately disconnect the iPhone from the case and stop charging.
• Allow Cooling: Let both devices cool down completely before attempting to use or charge again.
• Environmental Factors: Avoid charging in direct sunlight or enclosed spaces with poor ventilation.

7.4 Data Sync Not Working

• Cable Connection: Ensure the Lightning cable is securely connected between the case (with iPhone inside) and your computer.
• Computer Recognition: Check if your computer recognizes the iPhone. You may need to unlock your iPhone and trust the computer.
• Restart Devices: Try restarting both your iPhone and computer.

8. Specifications

9. Warranty and Support

Pxwaxpy offers product quality support for 12 months from the date of purchase. This includes a 30-day no-hassle return policy. For any inquiries or support, please contact Pxwaxpy customer service. They provide 24-hour online service.

Please retain your proof of purchase for warranty claims.