1. Introduction
This manual provides comprehensive instructions for the safe installation, operation, and maintenance of your V-TAC VT-702 GU10 Shower Fire Rated Downlight Fitting. Please read this manual thoroughly before installation and retain it for future reference. This product is designed for indoor use, specifically in areas requiring IP65 and fire-rated protection, such as bathrooms and kitchens.
2. Safety Information
- Electrical Installation: Installation must be carried out by a qualified electrician in accordance with all local and national wiring regulations.
- Power Disconnection: Always ensure the main power supply is switched off at the consumer unit/fuse box before commencing any installation, maintenance, or repair work.
- Product Integrity: Do not modify or alter the product in any way. Any modifications will void the warranty and may pose a safety risk.
- Fire Rating: This downlight is fire-rated for 90 minutes. Ensure proper installation to maintain its fire integrity. Do not remove or damage the fire-rated components.
- IP65 Rating: The IP65 rating signifies protection against dust ingress and low-pressure water jets from any direction. This makes it suitable for bathroom zones 1 and 2. Ensure all seals are correctly seated during installation to maintain this rating.
- Bulb Compatibility: Use only GU10 LED bulbs. Ensure the bulb's wattage does not exceed the maximum specified for the fitting (check bulb manufacturer's specifications). Bulbs are not included.
- Heat: Allow the fitting and bulb to cool down before handling or replacing the bulb.
3. Product Overview
The V-TAC VT-702 is a high-quality, fire-rated, and IP65-rated downlight fitting designed for recessed installation. It features a satin nickel finish and is compatible with standard GU10 LED bulbs.
Figure 3.1: Overview of the V-TAC VT-702 GU10 Downlight Fitting in satin nickel finish.
Figure 3.2: The downlight is fire-rated for 90 minutes, providing enhanced safety and compliance with building regulations. It includes air leak protection for fire safety.
Figure 3.3: Key dimensions of the GU10 fixed fire-rated downlight fitting. The cutting size required for installation is Ø65mm, with an overall diameter of Ø86mm and a height of 115mm.
Figure 3.4: The downlight features quick connectors for loop-in loop-out wiring, ensuring quicker and safer installation. Robust spring clips are provided for secure mounting in the ceiling.
Figure 3.5: The V-TAC VT-702 boasts an IP65 rating, making it water-resistant and protected against dust and low-pressure water jets. This makes it suitable for use in bathrooms and other damp environments.
Figure 3.6: The downlight is compatible with any standard GU10 lamp. Please note that bulbs are not included with the fitting and must be purchased separately.
4. Setup and Installation
Important: Installation should only be performed by a qualified electrician.
- Preparation: Ensure the main power supply to the circuit where the downlight will be installed is switched off at the consumer unit/fuse box.
- Ceiling Cut-out: Using a suitable hole saw, create a circular cut-out in the ceiling with a diameter of Ø65mm. Ensure there is sufficient clear space above the ceiling for the fitting and wiring, respecting fire safety regulations and insulation requirements.
- Wiring: Connect the electrical supply cables to the quick connectors provided on the downlight fitting. Ensure correct polarity (Live, Neutral, Earth) and secure all connections. The quick connectors facilitate loop-in loop-out wiring.
- Bulb Insertion: Insert a GU10 LED bulb (not included) into the lamp holder of the downlight fitting.
- Mounting: Fold back the spring clips on the sides of the downlight fitting. Carefully push the fitting into the prepared ceiling cut-out. The spring clips will automatically expand and secure the fitting firmly in place against the ceiling.
- Final Check: Ensure the fitting is securely seated and flush with the ceiling surface.
- Power Restoration: Restore power to the circuit at the consumer unit/fuse box and test the downlight.
5. Operating Instructions
The V-TAC VT-702 downlight operates via a standard wall switch connected to its electrical circuit. Once installed and wired correctly, simply toggle the wall switch to turn the light on or off.
- Ensure a compatible GU10 LED bulb is correctly inserted into the fitting.
- The fitting is designed for continuous use within its specified voltage range (220 Volts).
6. Maintenance
Regular maintenance will ensure the longevity and optimal performance of your downlight fitting.
- Cleaning: Disconnect power before cleaning. Wipe the fitting with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish. For stubborn marks, a slightly damp cloth can be used, ensuring no moisture enters the electrical components.
- Bulb Replacement:
- Switch off the power supply to the downlight at the main consumer unit/fuse box.
- Allow the bulb to cool completely if it has been in use.
- Carefully remove the old GU10 bulb by twisting it counter-clockwise.
- Insert the new GU10 LED bulb by aligning the pins with the lamp holder slots and twisting clockwise until secure.
- Restore power and test the new bulb.
- Inspection: Periodically inspect the fitting for any signs of damage or wear. If any damage is observed, disconnect power and consult a qualified electrician.
7. Troubleshooting
If your V-TAC VT-702 downlight is not functioning correctly, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Faulty bulb. Loose wiring connection. | Check if the main power switch is on. Check if the circuit breaker has tripped. Replace the GU10 bulb. (For loose wiring) Disconnect power and have a qualified electrician check the connections. |
| Light flickers. | Incompatible bulb. Loose bulb connection. Voltage fluctuations. | Ensure you are using a compatible GU10 LED bulb. Ensure the bulb is securely twisted into the lamp holder. Consult an electrician if voltage issues are suspected. |
| Fitting is hot to touch. | Over-wattage bulb. Insufficient ventilation. | Ensure the bulb wattage does not exceed the recommended maximum for the fitting. Ensure proper air circulation around the fitting in the ceiling void. |
If the problem persists after attempting these solutions, please contact a qualified electrician or V-TAC customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | V-TAC |
| Model Number | VT-702 |
| Part Number | 3683 |
| Type | GU10 Recessed Downlight Fitting |
| Colour | Nickel (Satin Finish) |
| Material | Nickel / Alloy Steel |
| Voltage | 220 Volts |
| IP Rating | IP65 (Water Resistant) |
| Fire Rating | 90 Minutes Fire Rated |
| Cutting Size | Ø65mm |
| Overall Diameter | Ø86mm |
| Height | 115mm |
| Bulb Type | GU10 (Bulb not included) |
| Included Components | Mounting Hardware, Screws |
| Item Weight | 250 g |
9. Warranty and Support
For warranty information, please refer to the terms and conditions provided by your retailer at the time of purchase. V-TAC products typically come with a manufacturer's warranty against defects in materials and workmanship.
For technical support or further assistance, please contact V-TAC customer service or visit their official website. You can find more information about V-TAC products at the V-TAC Store on Amazon.
