1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Kingston Brass KS2986AX Governor Widespread Bathroom Faucet. Please read all instructions carefully before beginning installation to ensure proper function and longevity of your product. This faucet features solid brass construction, a drip-free ceramic disc cartridge, and is designed for a 3-hole widespread installation.
2. Safety Information
Always turn off the main water supply before installing or performing any maintenance on the faucet. Wear appropriate personal protective equipment, such as safety glasses, during installation. If you are unsure about any part of the installation process, consult a qualified plumber. Do not overtighten connections, as this may damage the product or plumbing.
3. Included Components
Verify that all components are present before beginning installation.
- Faucet Spout Assembly
- Hot and Cold Handle Assemblies
- Mounting Hardware
- Brass Pop-Up Drain Assembly
- Water Supply Lines (typically included or purchased separately)
Image: All components of the Kingston Brass KS2986AX Governor Widespread Bathroom Faucet, including the spout, handles, and pop-up drain.
4. Tools Required
The following tools are typically required for installation:
- Adjustable Wrench
- Phillips Head Screwdriver
- Plumber's Putty or Silicone Sealant
- Thread Seal Tape (Teflon Tape)
- Basin Wrench (optional, for tight spaces)
- Safety Glasses
5. Setup and Installation
This faucet is designed for a deck mount 8" to 16" widespread 3-hole installation with standard 1/2" IPS connections.
5.1 Prepare the Installation Area
- Turn off the main water supply to the bathroom.
- Remove any existing faucet and clean the sink surface thoroughly.
- Ensure the sink has three mounting holes, spaced between 8 and 16 inches apart.
5.2 Install Faucet Handles
- Apply a thin bead of plumber's putty or silicone sealant around the base of each handle assembly.
- Insert the handle shanks through the outer holes of the sink deck.
- From underneath the sink, secure each handle with the provided washers and mounting nuts. Hand-tighten, then use a wrench for a final snug turn. Do not overtighten.
Image: Close-up view of the hot and cold cross handles, showing their design and labeling.
5.3 Install Faucet Spout
- Apply plumber's putty or silicone sealant around the base of the faucet spout.
- Insert the spout shank through the center hole of the sink deck.
- From underneath, secure the spout with the provided washer and mounting nut. Tighten securely.
Image: Detailed view of the faucet spout, highlighting its polished nickel finish and elegant curve.
5.4 Connect Water Supply Lines
- Connect the hot and cold water supply lines to the corresponding inlets on the handle assemblies. Use thread seal tape on threaded connections.
- Connect the other ends of the supply lines to your hot and cold water stops.
- Connect the flexible hoses from the handle assemblies to the faucet spout's inlet.
5.5 Install Pop-Up Drain
- Disassemble the pop-up drain assembly.
- Apply plumber's putty or silicone sealant to the underside of the drain flange.
- Insert the drain flange into the sink drain hole.
- From underneath, install the rubber washer, friction washer, and mounting nut onto the drain body. Tighten securely.
- Connect the pop-up rod to the drain stopper and the lift rod from the faucet spout.
Image: Exploded view diagram of a drain with overflow, illustrating components like the clevis screw, spring clip, plunger, and clevis strap for proper assembly.
5.6 Final Steps
- Turn on the main water supply slowly and check for any leaks.
- Run both hot and cold water through the faucet for a few minutes to flush out any debris.
Image: Technical diagram showing the dimensions and connection points for the Kingston Brass widespread lavatory faucet, model KS2980AX series.
6. Operating Instructions
Your Kingston Brass Governor faucet features two cross handles for precise control of water temperature and flow.
- Cold Water: Turn the right handle counter-clockwise to open for cold water.
- Hot Water: Turn the left handle counter-clockwise to open for hot water.
- Temperature Control: Adjust the hot and cold handles simultaneously to achieve the desired water temperature.
- Flow Rate: The faucet has a flow rate of 1.2 Gallons Per Minute (GPM) at 60 PSI.
Image: A close-up view of one of the cross handles, indicating its function for water control.
7. Maintenance
Proper care and maintenance will ensure the lasting beauty and performance of your faucet.
7.1 Cleaning
- Clean the faucet regularly with a soft cloth and warm, soapy water.
- Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the polished nickel finish.
- Rinse thoroughly after cleaning and dry with a soft cloth to prevent water spots.
7.2 Ceramic Disc Cartridge
Your faucet is equipped with a drip-free ceramic disc cartridge, designed for long-term reliability. If a leak occurs from the handles, the cartridge may need to be replaced. Contact customer support for replacement parts.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Faucet leaks from handle | Worn ceramic disc cartridge | Replace the ceramic disc cartridge. |
| Low water flow | Aerator clogged with debris | Unscrew the aerator from the spout, clean out any debris, and reattach. |
| Water leaks from base of faucet | Loose mounting nuts or improper sealant | Tighten mounting nuts or reapply plumber's putty/silicone sealant. |
| Pop-up drain does not seal | Improper adjustment of pop-up rod or worn stopper seal | Adjust the clevis strap on the pop-up rod. Inspect and replace the stopper seal if necessary. |
9. Specifications
| Feature | Detail |
|---|---|
| Brand | Kingston Brass |
| Model Number | KS2986AX |
| Model Name | Kingston Brass Governor |
| Finish Type | Polished Nickel |
| Material | Solid Brass |
| Mounting Type | Deck Mount |
| Hole Count | 3 |
| Installation Method | Widespread (8" to 16" centers) |
| Number of Handles | 2 (Cross Handles) |
| Flow Rate | 1.2 GPM (4.5 LPM) at 60 PSI |
| Spout Height | 11.5 Inches |
| Spout Reach | 6.31 Inches |
| Item Weight | 8.4 Pounds |
| Included Components | Faucet, Mounting Hardware, Pop-Up Drain |
| UPC | 663370550218 |
10. Warranty Information
This Kingston Brass faucet comes with a limited warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the warranty documentation included with your purchase or visit the official Kingston Brass website. Keep your proof of purchase for warranty claims.
11. Customer Support
If you have any questions, require technical assistance, or need to order replacement parts, please contact Kingston Brass customer support:
- Website: www.kingstonbrass.com
- Phone: Refer to the Kingston Brass website for current contact numbers.
- Email: Refer to the Kingston Brass website for customer service email.
Please have your model number (KS2986AX) and purchase date available when contacting support.
