Urmet 5454601 Wall-Mounted Radio Touch Switch Instruction Manual

Introduction

This manual provides instructions for the installation, operation, and maintenance of your Urmet 5454601 Wall-Mounted Radio Touch Switch. This device is a two-button radio transmitter designed for wall mounting and functions as an accessory for compatible radio receivers (e.g., Urmet article 545454556). Please refer to the receiver's manual for full system integration and specific pairing procedures.

Image Description: A white, rectangular wall-mounted radio touch switch with two distinct touch areas separated by a thin horizontal line. The switch features a sleek, modern design with a chrome-like metallic trim around the touch surface. The "Yokis" brand logo is subtly visible in the bottom right corner.

Safety Information

Read all instructions carefully before installation and use to ensure safe and proper operation.

• Installation should be performed by a qualified electrician in accordance with local electrical codes.
• Always disconnect power to the circuit at the main breaker before attempting any installation or maintenance.
• Do not expose the device to moisture, direct water spray, or extreme temperatures.
• This device is a radio transmitter accessory and requires a compatible radio receiver for full functionality.

Setup and Installation

Step 1: Preparation

Ensure the power supply to the installation area is turned off at the main circuit breaker. Gather necessary tools such as a screwdriver.

Step 2: Mounting the Switch

The Urmet 5454601 is designed for surface wall mounting or installation into a standard electrical box.

1. Carefully remove the front plate of the switch to access the mounting holes.
2. Position the switch base on the desired wall location or within an electrical box.
3. Secure the switch base using appropriate screws, ensuring it is level and firmly attached.

Step 3: Wiring (if applicable)

As a radio transmitter, this device typically does not require direct mains wiring. If your specific installation requires low-voltage wiring or battery insertion, connect according to the specific wiring diagram provided with the main system or insert batteries as indicated. The product specifications state that batteries are neither required nor included for this model.

Step 4: Pairing with Receiver

Refer to the instruction manual of your compatible radio receiver (e.g., Urmet 545454556) for specific pairing procedures. Generally, this involves putting the receiver into a pairing mode and then activating the transmitter buttons on the 5454601 switch.

Step 5: Final Assembly

Once mounted and (if applicable) wired/paired, reattach the front plate of the switch. Restore power to the circuit at the main breaker.

Operating Instructions

The Urmet 5454601 features two distinct touch areas for control, allowing for dual functionality.

• Upper Touch Area: Typically used for one function (e.g., "ON," "UP," or a specific scene activation).
• Lower Touch Area: Typically used for a second function (e.g., "OFF," "DOWN," or another scene activation).

The specific function of each touch area is determined by the programming of the paired receiver. To activate a function, gently touch the corresponding area on the switch. The touch sensitivity is designed for light contact.

Maintenance

Cleaning

• Always disconnect power to the circuit before cleaning the switch.
• Use a soft, dry, or slightly damp cloth to gently wipe the surface.
• Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish and internal components.

Troubleshooting

Issue: Switch does not respond.

• Check Power: Ensure power is restored to the circuit (if wired) or that the device is correctly powered.
• Pairing: Verify that the switch is correctly paired with its receiver. Re-initiate the pairing process if necessary (refer to the receiver's manual).
• Receiver Functionality: Confirm the receiver is powered and functioning correctly.
• Obstructions/Distance: Ensure there are no physical obstructions or excessive distance between the switch and the receiver that could interfere with the radio signal.

Issue: Incorrect function when touched.

• Reprogramming: The switch's functions are determined by the receiver's programming. Refer to the receiver's manual to reprogram the desired actions for each touch area.

If problems persist after attempting these troubleshooting steps, contact a qualified technician or Urmet customer support for further assistance.

Specifications

Warranty and Support

Specific warranty information for the Urmet 5454601 is not provided in the product details. Please refer to your purchase documentation or contact Urmet customer service for detailed warranty terms and technical support.

For further assistance, visit the official Urmet website or contact your local distributor for product inquiries and service.