ECLIPSE KW-218T Direct Conversion Cord Instruction Manual

Introduction

This manual provides essential instructions for the proper installation, operation, and maintenance of your ECLIPSE KW-218T Direct Conversion Cord. This cord is designed to facilitate the connection of a 16-pin car navigation unit to the manufacturer's wiring harness in compatible Toyota and Daihatsu vehicles. Please read this manual thoroughly before installation to ensure correct usage and prevent damage.

Setup and Installation

The KW-218T Direct Conversion Cord simplifies the connection process between your car navigation system and the vehicle's existing wiring. It is specifically designed for Toyota and Daihatsu vehicles utilizing 10-pin, 6-pin, 20-pin, and 28-pin connectors.

Package Contents

• ECLIPSE KW-218T Direct Conversion Cord

Installation Steps

1. Preparation: Ensure the vehicle's battery is disconnected before beginning any electrical work to prevent short circuits or damage.
2. Access Vehicle Harness: Carefully remove the necessary trim panels and the existing car audio/navigation unit to access the vehicle's wiring harness. Refer to your vehicle's service manual for specific instructions on panel removal.
3. Identify Connectors: Locate the 10-pin, 6-pin, 20-pin, and 28-pin connectors on your Toyota or Daihatsu vehicle's wiring harness.
4. Connect Conversion Cord: Connect the corresponding ends of the KW-218T Direct Conversion Cord to the vehicle's wiring harness connectors. Ensure all connections are secure and fully seated.
5. Connect to Navigation Unit: Connect the 16-pin connector of the KW-218T cord to the designated 16-pin input on your car navigation system.
6. Secure Wiring: Route and secure all wiring to prevent pinching, chafing, or interference with moving parts. Use cable ties if necessary.
7. Test Functionality: Reconnect the vehicle's battery. Power on the car navigation unit and test all functions (audio, navigation, etc.) to confirm proper installation.
8. Reassemble: Once functionality is confirmed, carefully reassemble all removed trim panels.

Image 1: The ECLIPSE KW-218T Direct Conversion Cord. This image displays the various connectors and wiring of the conversion cord, designed to interface between a car navigation unit and a Toyota/Daihatsu vehicle's wiring harness.

Image 2: Diagram illustrating the difference between a direct conversion cord and a standard conversion cord. The direct conversion cord (KW-****D) connects directly from the navigation unit's rear connector to the vehicle's harness, offering a streamlined connection. A standard conversion cord (KW-****) typically involves additional connections, such as Giboshi terminals, to the vehicle's harness. This diagram helps visualize the simplified wiring provided by the direct conversion type.

Operation

The KW-218T Direct Conversion Cord is a passive component that facilitates electrical connections. Once correctly installed, its operation is integrated with your car navigation system. It does not require separate user interaction or controls. The cord ensures that power, ground, and signal lines are correctly routed between the navigation unit and the vehicle's electrical system, allowing the navigation unit to function as intended.

Maintenance

The ECLIPSE KW-218T Direct Conversion Cord is designed for long-term reliability and requires minimal maintenance. Follow these guidelines to ensure its longevity:

• Secure Installation: Ensure the cord and its connections remain securely fastened within the vehicle's dashboard or paneling. Loose connections can lead to intermittent issues.
• Avoid Stress: Do not pull, twist, or apply excessive force to the cord or its connectors. This can damage the internal wiring or connector pins.
• Keep Dry: Protect the cord from moisture and liquids. While designed for automotive environments, excessive exposure to water can cause corrosion or electrical faults.
• Regular Inspection: If you experience any electrical issues with your car navigation system, a visual inspection of the cord and its connections for signs of wear, damage, or corrosion may be beneficial.

Troubleshooting

If you encounter issues after installing the KW-218T Direct Conversion Cord, consider the following troubleshooting steps:

• No Power to Navigation Unit:
  • Check the vehicle's fuse box for any blown fuses related to the car audio or accessory power.
  • Ensure the KW-218T cord's power (ACC, B+) and ground connections are securely attached to the vehicle's harness.
  • Verify the 16-pin connector is fully seated into the car navigation unit.
• No Audio Output:
  • Confirm that the speaker wires from the KW-218T are correctly connected to the navigation unit and the vehicle's speaker harness.
  • Check the navigation unit's audio settings.
• Intermittent Functionality:
  • Inspect all connections for looseness or corrosion.
  • Ensure the wiring is not pinched or damaged by vehicle components.
• Incorrect Pin Configuration:
  • Double-check that the KW-218T is the correct conversion cord for your specific vehicle model and year, as wiring configurations can vary.

If problems persist after performing these checks, it is recommended to consult a professional automotive electronics technician.

Specifications

Warranty Information

Specific warranty details for the ECLIPSE KW-218T Direct Conversion Cord may vary by region and retailer. Please retain your proof of purchase. For information regarding warranty coverage, terms, and conditions, refer to the documentation provided at the time of purchase or contact your authorized ECLIPSE dealer or the retailer from whom the product was acquired.

Customer Support

For technical assistance, installation queries, or further information regarding the ECLIPSE KW-218T Direct Conversion Cord, please contact your product retailer or an authorized ECLIPSE service center. When contacting support, please have your product model number (KW-218T) and purchase details readily available.