NOYITO NOPWMMS20A

Download PDF
Contents

NOYITO NOPWMMS20A PWM DC Motor Speed Controller User Manual

Model: NOPWMMS20A | Brand: NOYITO

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your NOYITO NOPWMMS20A PWM DC Motor Speed Controller. This device is designed to control the speed of a brush DC motor by adjusting the Pulse Width Modulation (PWM) signal. Please read this manual thoroughly before use to ensure proper function and safety.

Safety Information

  • Ensure the input voltage is within the specified range of DC 6V-60V. Exceeding this range can damage the device.
  • Always disconnect power before making any wiring connections or adjustments.
  • Do not exceed the continuous current rating of 20A or the maximum current of 30A. Overload protection is provided by a fuse, but continuous overload can lead to component failure.
  • This controller is designed for brush DC motors only. Do not use with AC motors or other motor types.
  • Keep the device away from moisture, dust, and extreme temperatures.
  • Ensure proper ventilation around the controller, especially the heat sinks, to prevent overheating.

Package Contents

Verify that all items are present in the package:

  • 1x NOYITO NOPWMMS20A PWM DC Motor Speed Controller

Product Overview

The NOYITO NOPWMMS20A is a robust PWM motor speed controller featuring a digital display for speed percentage and a potentiometer with an integrated switch function. It is equipped with heat sinks for efficient heat dissipation and screw terminals for secure wiring.

NOYITO PWM DC Motor Speed Controller with potentiometer and digital display

Figure 1: Top view of the NOYITO PWM DC Motor Speed Controller, showing the main circuit board, heat sinks, digital display, and the connected potentiometer.

Close-up top view of the NOYITO PWM DC Motor Speed Controller components

Figure 2: Detailed top view highlighting the capacitors, fuse, heat sinks, and screw terminals on the controller board.

Setup and Wiring

Follow these steps to correctly connect the motor speed controller:

  1. Power Source Connection: Connect your DC power supply (6V-60V) to the "+POWER" and "-POWER" terminals. Ensure correct polarity. The "+POWER" terminal is for the positive lead, and "-POWER" is for the negative lead.
  2. Motor Connection: Connect your brush DC motor to the "+MOTOR" and "-MOTOR" terminals. The polarity for the motor connection can be reversed to change the motor's direction of rotation if needed.
  3. Potentiometer Connection: The potentiometer is pre-wired to the controller board. Ensure the connector is securely seated.
  4. Secure Connections: Double-check all wiring connections to ensure they are tight and secure to prevent loose contacts and potential short circuits.
Bottom view of the NOYITO PWM DC Motor Speed Controller showing power and motor terminals

Figure 3: Bottom view of the controller board, clearly indicating the "+POWER", "-POWER", "+MOTOR", and "-MOTOR" connection points for wiring.

Angled view of the NOYITO PWM DC Motor Speed Controller showing terminal blocks

Figure 4: Angled view showing the screw terminal blocks for power input and motor output connections, along with the fuse holder.

Operating Instructions

Once the controller is wired correctly, follow these steps to operate it:

  1. Power On: Apply power to the controller. The digital display will illuminate.
  2. Turn On/Off: The potentiometer knob has an integrated switch function. Rotate the knob clockwise from the "OFF" position to turn on the controller and begin speed adjustment. Rotate counter-clockwise to the "OFF" position to turn off the controller.
  3. Adjust Speed: Rotate the potentiometer knob clockwise to increase the motor speed and counter-clockwise to decrease it. The digital display will show a percentage (0-100), which represents the percentage of the motor's full speed. This is not the actual RPM of the motor.
  4. Monitoring: Observe the digital display to monitor the speed setting.
NOYITO PWM DC Motor Speed Controller with focus on the potentiometer

Figure 5: View of the controller highlighting the potentiometer knob, used for both turning the device on/off and adjusting the motor speed.

Maintenance

  • Cleaning: Keep the controller clean and free from dust. Use a soft, dry cloth for cleaning. Do not use liquids or abrasive cleaners.
  • Ventilation: Ensure that the heat sinks are not obstructed to allow for proper airflow and heat dissipation.
  • Connections: Periodically check all wiring connections for tightness and signs of wear or corrosion.
  • Fuse Replacement: If the controller stops functioning due to an overload, check the fuse. Replace it with a fuse of the same type and rating (e.g., 30A fast-blow fuse). Always disconnect power before replacing the fuse.

Troubleshooting

ProblemPossible CauseSolution
Controller does not power on / Digital display is off.
  • No power input.
  • Incorrect power polarity.
  • Blown fuse.
  • Potentiometer knob is in "OFF" position.
  • Check power supply connection and ensure it's active.
  • Verify "+POWER" and "-POWER" connections.
  • Inspect and replace the fuse if blown (ensure power is off).
  • Rotate potentiometer knob clockwise to turn on.
Motor does not run or runs intermittently.
  • Loose motor connections.
  • Motor fault.
  • Controller output fault.
  • Motor current exceeds controller's maximum.
  • Check "+MOTOR" and "-MOTOR" connections.
  • Test motor independently if possible.
  • Ensure motor current draw is within 20A continuous / 30A max.
Speed adjustment is not responsive.
  • Faulty potentiometer.
  • Loose potentiometer connection.
  • Check the potentiometer's wiring connection to the board.
  • Contact support if potentiometer is suspected to be faulty.
Controller overheats.
  • Insufficient ventilation.
  • Motor drawing excessive current.
  • Operating in high ambient temperature.
  • Ensure heat sinks are clear and airflow is adequate.
  • Verify motor current draw is within specifications.
  • Operate in a cooler environment if possible.

Specifications

ParameterValue
Input VoltageDC 6V-60V
Output VoltageLoad Linear
Continuous Current20A
Maximum Current30A
Speed Control MethodPotentiometer with switch function
Speed ModeON / OFF linear potentiometer 270 degrees
Speed Range0-100% (Digital display shows percentage of full speed)
Speed TypeRegulating current
Operating Frequency15KHZ
Dimensions (L*W*H)75 x 56 x 28 mm (2.95 x 2.2 x 1.1 inches)
Weight75g (2.61 ounces)
Model NumberNOPWMMS20A
MaterialMetal

Warranty Information

This NOYITO product is covered by a Manufacturer's One-year After-sale Warranty. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.

Customer Support

For technical assistance, troubleshooting, or warranty inquiries, please contact NOYITO customer support. Refer to the product packaging or the seller's information for contact details.

© 2026 NOYITO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.