XIHADA Universal Remote Cloner Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the setup, operation, and maintenance of your XIHADA Universal Remote Cloner. This device is designed to duplicate signals from existing garage door openers and gate remotes, offering a convenient multi-frequency solution. Please read these instructions carefully before use to ensure proper functionality and to avoid any issues.

Image 1: XIHADA Universal Remote Cloner (Green variant)

2. Safety Information

• Keep the remote control out of reach of children to prevent accidental operation.
• Do not expose the remote to water or extreme temperatures.
• Ensure the garage door or gate area is clear of obstructions before operating.
• Only attempt programming when you have a clear understanding of the steps. If unsure, consult the manufacturer's support.

3. Package Contents

• 1 x XIHADA Universal Remote Cloner (ML999-17)
• 1 x CR2032 Battery (pre-installed)
• Instruction Manual (this document)

4. Product Overview

The XIHADA Universal Remote Cloner features a compact design with four programmable buttons, allowing you to consolidate up to four different remote functions into a single device. It supports multiple frequencies ranging from 280MHz to 868MHz.

Image 2: Remote button identification (Key 1, Key 2, Key 3, Key 4)

Image 3: Remote dimensions (2.36 inches / 6.0 cm length, 1.38 inches / 3.5 cm width)

5. Compatibility

Before attempting to program, it is crucial to verify that your existing remote control and opener system are compatible with the XIHADA Universal Remote Cloner. This device is designed to clone signals from a wide range of brands and models, but not all. You must have a working original remote to perform the cloning process.

Compatible Brands and Models:

Refer to the compatibility list provided by the manufacturer. A visual representation of a partial compatibility list is shown below. For a complete and updated list, please consult the product listing page or manufacturer's website.

Image 4: Partial compatibility list for various remote brands and models.

Non-Compatible Brands and Models:

The XIHADA Universal Remote Cloner is not compatible with the following brands and models:

• Chamberlain / Liftmaster Security 2.0, 2.0+ Garage Door Opener
• Chamberlain Garage door Opener with MYQ / Liftmaster Garage Door Opener with MYQ
• LiftMaster 8500W Garage Door Opener
• Liftmaster 892LT / LiftMaster 811LMX / LiftMaster 893LM
• Chamberlain B 6713T Garage Opener / Chamberlain B 6753T Smart Garage Opener
• Condo's garage door opener, Ryobi, Softens Doors, Blue Sea, Allister, Amarr, Atoms, Doorking/DKS, Lynx, Merik, Stanley, Skylink, Wayne Dalton, Martin, Saco Gate Opener.

6. Setup (Programming Instructions)

The XIHADA Universal Remote Cloner can duplicate signals from up to four different original remotes. The programming process involves two main steps: cloning the signal from your original remote to the universal remote, and for garage door openers, potentially pairing with the opener's receiver.

Cloning Process (Rolling Code Simple - Act on the Opener Receiver):

Image 5: Visual guide for the remote cloning process.

1. Clear Existing Codes: Hold down button 1 (top left) and then press button 2 (top right) four times on the universal remote. Release both buttons. The LED on the universal remote will flash every 2 seconds, indicating it is ready for learning.
2. Clone Original Remote: Place your original remote very close to the universal remote, ideally back-to-back or face-to-face, ensuring they are touching. Hold down the button on your original remote that you wish to copy. The LED on the universal remote will start to flash quickly, indicating it is now learning codes from your original remote.
3. Store Code: While the LED of the universal remote is flashing quickly, press any button on the universal remote where you want to store the remote's code. The LED will turn off once the code is successfully copied.
4. Pair with Opener (for Garage Doors): For garage door openers, an additional step is often required. Press the 'LEARN' button on your garage door opener receiver (the mechanical unit that opens the door). The LED on your garage door opener should illuminate.
5. Activate Opener: Immediately after pressing the 'LEARN' button on the opener, press the button you just programmed on the universal remote. The lights on your garage door opener should either flash or go on and off depending on the brand of the opener, confirming successful pairing.
6. You can now test the functionality of the universal remote to open your garage door or gate.

Note: If you encounter difficulties, refer to the manufacturer's detailed programming video, which may be available on their product listing page or website.

7. Operating

Once successfully programmed, operating the XIHADA Universal Remote Cloner is straightforward. Simply press the corresponding button on the remote that you have programmed for your garage door or gate. Ensure you are within the effective transmission range for reliable operation.

Image 6: Remote being used to open a garage door from inside a vehicle.

Image 7: Remote being used to open an automatic gate.

8. Maintenance

Battery Replacement:

The remote uses one CR2032 3V lithium battery. When the remote's range decreases or the LED indicator becomes dim, it is time to replace the battery. To replace, carefully open the remote casing (often by unscrewing a small screw or prying gently along the seam) and replace the old battery with a new CR2032, ensuring correct polarity.

Cleaning:

Wipe the remote with a soft, dry cloth. Do not use abrasive cleaners or immerse the remote in liquids.

9. Troubleshooting

• Remote not programming:
  • Ensure your original remote is working correctly and has a strong battery.
  • Verify that your original remote and opener system are listed as compatible (refer to Section 5).
  • Make sure the universal remote's existing codes are cleared before attempting to clone.
  • Ensure the original remote and universal remote are in close contact during the cloning step.
  • If cloning a rolling code, ensure you complete the pairing step with your garage door opener's 'LEARN' button.
• Short operating range:
  • Replace the battery in the universal remote.
  • Ensure there are no major obstructions between the remote and the receiver.
• Remote LED does not light up:
  • Check or replace the CR2032 battery.

10. Specifications

11. Warranty and Support

For warranty information or technical support, please refer to the product's original purchase documentation or contact XIHADA customer service through the retailer where the product was purchased. Ensure you have your model number (ML999-17) and purchase details available when seeking support.