1. Introduction
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your TEXAS XC 160-108H Ride-On Mower. Please read this manual thoroughly before operating the machine to ensure proper use and to prevent injury or damage.
Figure 1.1: Overview of the TEXAS XC 160-108H Ride-On Mower. This image shows the complete ride-on mower from a front-left angle, highlighting its compact design, large wheels, and the cutting deck.
2. Safety Instructions
Always prioritize safety when operating the ride-on mower. Failure to follow these instructions can result in serious injury or death.
- Read and understand all instructions before operating the machine.
- Keep children and pets away from the operating area.
- Wear appropriate personal protective equipment (PPE), including eye protection, hearing protection, and sturdy footwear.
- Never operate the mower under the influence of alcohol or drugs.
- Inspect the area for debris before mowing.
- Do not operate on excessively steep slopes.
- Turn off the engine and remove the key before performing any maintenance or clearing blockages.
3. Setup and Assembly
Your TEXAS XC 160-108H Ride-On Mower may require some assembly upon delivery. Follow these steps carefully.
- Unpacking: Carefully remove all components from the packaging. Check for any shipping damage.
- Steering Wheel Installation: Attach the steering wheel to the steering column, ensuring it is securely fastened.
- Seat Installation: Mount the operator's seat onto the designated frame, securing it with the provided hardware.
- Battery Connection: Connect the battery terminals, ensuring correct polarity (red to positive, black to negative).
- Fluid Checks: Before first use, check engine oil level and fuel level. Refer to the "Specifications" section for recommended fluid types and capacities.
Figure 3.1: Top-down view of the operator's station, showing the steering wheel, seat, and control levers. This image helps in identifying key controls during setup and operation.
4. Operating Instructions
Familiarize yourself with the controls and operating procedures before starting the engine.
4.1. Pre-Operation Checklist
- Check engine oil level.
- Ensure fuel tank is adequately filled with gasoline.
- Inspect tires for proper inflation.
- Verify cutting deck is clear of debris.
- Adjust seat for comfortable operation.
4.2. Starting the Engine
- Ensure the parking brake is engaged.
- Place the cutting deck engagement lever in the "disengaged" position.
- Insert the key into the ignition switch.
- Turn the key to the "START" position. The 12V electric start system will engage the engine.
- Once the engine starts, release the key.
4.3. Mowing Operation
- Cutting Height Adjustment: Use the 7-fold central adjustment lever to set the desired cutting height between 30 mm and 90 mm.
- Speed Control: The hydrostatic transmission allows for stepless speed adjustment from 0 to 8.8 km/h using the foot pedal.
- Side Discharge: The mower features a side discharge chute for efficient grass dispersal. Ensure the chute is clear during operation.
Figure 4.1: Detail of the side discharge chute. This component directs cut grass away from the mower, preventing clumping and ensuring a clean cut.
5. Maintenance
Regular maintenance is crucial for the longevity and optimal performance of your ride-on mower.
5.1. Engine Maintenance
- Oil Change: Change engine oil (SAE 30) after the first 5 hours of operation, then every 25 hours or annually.
- Air Filter: Clean or replace the air filter regularly, especially in dusty conditions.
- Spark Plug: Inspect and clean the spark plug annually. Replace if worn.
5.2. Cutting Deck and Blades
- Blade Sharpening/Replacement: Sharpen or replace blades as needed to ensure a clean cut. Always wear gloves when handling blades.
- Deck Cleaning: Clean the underside of the cutting deck after each use to prevent grass buildup.
5.3. General Maintenance
- Tire Pressure: Check tire pressure regularly.
- Lubrication: Lubricate all moving parts as indicated in the service diagram (not provided, but a general instruction).
- Storage: Store the mower in a dry, protected area when not in use.
6. Troubleshooting
This section provides solutions to common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Engine does not start | No fuel; Dead battery; Spark plug issue; Safety switch engaged | Add fuel; Charge/replace battery; Check/replace spark plug; Ensure parking brake is on and deck is disengaged |
| Poor cutting performance | Dull blades; Deck clogged; Incorrect cutting height | Sharpen/replace blades; Clean deck; Adjust cutting height |
| Mower vibrates excessively | Bent blade; Loose components | Inspect/replace blade; Tighten all fasteners |
7. Specifications
Detailed technical specifications for the TEXAS XC 160-108H Ride-On Mower.
| Feature | Specification |
|---|---|
| Model | XC 160-108H (90063131) |
| Engine Type | Loncin 4-Stroke |
| Displacement | 452 cm³ |
| Power Output | 9.2 kW / 12.5 PS |
| Fuel Type | Gasoline |
| Fuel Tank Volume | 7.5 Liters |
| Engine Oil Type | SAE 30 |
| Engine Oil Volume | 1.2 Liters |
| Cutting Width | 108 cm |
| Cutting Height Adjustment | 7-fold, 30 - 90 mm |
| Starter | 12V Electric Start |
| Transmission | Hydrostatic (American Hydro-Gear) |
| Speed Range | 0 - 8.8 km/h |
| Turning Circle | 45 cm |
| Tire Size (Front/Rear) | Front: 15", Rear: 18" (Pneumatic) |
| Housing Material | Steel |
| Sound Power Level | 100 dB(A) |
| Dimensions (L x W x H) | 173 cm x 132 cm x 105 cm |
| Weight | 170 kg |
8. Warranty and Support
For warranty information and customer support, please refer to the documentation provided with your purchase or contact Texas customer service directly. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.
For further assistance, visit the official Texas website or contact their authorized service centers.
