Compustar 2-Way 4-Button FM Replacement Remote Transmitter Control 2WT9R-FM Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the Compustar 2WT9R-FM 2-Way 4-Button FM Replacement Remote Transmitter Control. This remote is designed to function with the Compustar RF-2WT9-FM system. It is crucial to verify compatibility with your existing system before attempting installation or use.

Compatibility Information:

• Designed for RF-2WT9-FM systems.
• Compatible Antenna Number: ANT-2WFMX.
• FCC ID: VA5RCD310-2WFX
• IC ID: 7087A-2WRCD310FX

2. Product Overview

The Compustar 2WT9R-FM remote offers advanced control and feedback for your vehicle's remote start and security system. Its 2-way communication provides confirmation of commands and vehicle status directly on its LCD screen.

2.1 Key Features

• 2-Way Communication: Receive visual and audible confirmations from your vehicle.
• 4-Button Design: Intuitive control for various functions.
• FM Technology: Enhanced range and signal reliability.
• LCD Display: Provides real-time vehicle status updates (e.g., lock status, engine status, battery level).
• Extended Range: Estimated operational range of up to 3000 feet.
• Power Source: Uses one AAA battery.

2.2 Remote Control Diagram

The image above displays the Compustar 2WT9R-FM remote control. The LCD screen shows icons for signal strength, lock status, engine status, and battery level. The side of the remote features four distinct buttons for various functions.

3. System Programming and Setup

This section outlines the process for flashing and updating your Compustar Blade module and controller, which is essential for the remote control to function correctly with your vehicle's system. This procedure requires a computer and specific hardware.

3.1 Required Items

• Computer (with Internet Explorer browser recommended)
• ADS-USB cable
• Compustar Controller (e.g., CM7200)
• Blade AL/TB Module

3.2 Programming Procedure

1. Create Account: Before starting, create an account on compustar.idatalink.com. It is recommended to use Internet Explorer and allow ActiveX if prompted.
2. Dock Blade Module: Carefully dock your Blade module into your Compustar Controller.
3. Connect ADS-USB: Plug the ADS-USB cable into an available USB port on your computer.
4. Connect Controller: Use the cable labeled "iDataLink module" to connect the ADS-USB to the black RS-232 data port on the Compustar Controller.
5. Access WebLink: Launch Internet Explorer and navigate to compustar.idatalink.com.
6. Flash Your Module: Click on the "Flash Your Module" option. The system will detect the connected hardware.
7. Select Vehicle: On the programming home screen, select the correct year, make, and model of your vehicle.
8. Configure and Flash: You can either configure specific features for the Blade module or select "Flash" to load the default settings. The site will provide the appropriate installation guide for download.
9. Flash Remote Starter: While the controller is still connected, select the "Remote Starter" tab. Here, you can configure additional features such as remote start run time, programmable outputs, and double pulse unlock. Save your changes. This tab also allows you to update the firmware for the controller when available.

3.3 System Programming Demonstration Video

3.4 Remote Pairing

After the system controller and module are properly flashed and installed in your vehicle, your 2WT9R-FM remote control will need to be paired or programmed to communicate with the system. Refer to your specific Compustar system's installation guide or consult a professional installer for detailed remote pairing instructions, as this process can vary.

4. Operation

The 2WT9R-FM remote control features four primary buttons, typically located on the side, and an LCD screen for visual feedback. While specific button assignments may vary based on system configuration, common functions include:

• Lock: Press to lock your vehicle's doors. The LCD will display a lock icon and provide confirmation.
• Unlock: Press to unlock your vehicle's doors. The LCD will display an unlock icon and provide confirmation.
• Remote Start: Press and hold (or press in sequence) to remotely start your vehicle's engine. The LCD will show an engine icon and countdown timer, confirming the start.
• Trunk Release / Auxiliary: Press to open the trunk or activate an auxiliary function (e.g., power sliding doors, heated seats).

The 2-way communication feature ensures that you receive visual and audible feedback on the remote's LCD screen, confirming that your commands have been executed by the vehicle.

5. Maintenance

5.1 Battery Replacement

The Compustar 2WT9R-FM remote control is powered by one AAA battery. When the battery level is low, an indicator will typically appear on the LCD screen. To replace the battery:

1. Locate the battery compartment cover on the back of the remote.
2. Carefully open the compartment using a small tool if necessary.
3. Remove the old AAA battery.
4. Insert a new AAA battery, ensuring correct polarity (+/-).
5. Close the battery compartment cover securely.

Dispose of old batteries according to local regulations.

6. Troubleshooting

If you encounter issues with your Compustar 2WT9R-FM remote control, consider the following common troubleshooting steps:

• No Response from Vehicle:
  • Check the remote's battery level and replace if necessary.
  • Ensure you are within the estimated 3000 ft. operating range.
  • Verify that the remote is properly paired with your Compustar system (refer to Section 3.4).
  • Check for strong radio interference in your current location.
• LCD Display Issues:
  • If the display is dim or unresponsive, replace the AAA battery.
  • If icons are incorrect, re-pair the remote with the system.
• Compatibility Concerns:
  • Confirm that your remote is the correct model (2WT9R-FM) for your Compustar RF-2WT9-FM system and ANT-2WFMX antenna. Incompatibility can lead to non-functionality.
• System Programming Errors:
  • If you suspect issues with the Blade module or controller firmware, re-perform the system programming steps outlined in Section 3.2.

For persistent issues or complex problems, it is recommended to contact Compustar technical support or an authorized installer.

7. Specifications

8. Warranty and Support

For information regarding product warranty, technical support, or to locate an authorized Compustar dealer, please visit the official Compustar website or contact their customer service department. Keep your purchase receipt as proof of purchase for any warranty claims.

Official Website: www.compustar.com

Technical Support: Refer to the contact information provided on the Compustar website or your product packaging.