1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Came Selt1Ndg Outdoor Keypad, model CMC806SL-0150. Please read this manual carefully before use to ensure proper functionality and safety.
The Came Selt1Ndg is a high-quality outdoor keypad designed for access control systems. It features a backlit keypad for enhanced visibility.
2. Safety Information
Always follow basic safety precautions to reduce the risk of injury, electric shock, or damage to the product.
- Installation should be performed by qualified personnel.
- Disconnect power before performing any maintenance or installation procedures.
- Do not expose the keypad to excessive moisture or extreme temperatures beyond its specified operating range.
- Ensure all connections are secure and properly insulated.
3. Package Contents
Verify that all components are present before beginning installation:
- Came Selt1Ndg Outdoor Keypad (1 unit)
- Mounting Screws and Anchors
- Instruction Manual (this document)
4. Setup and Installation
4.1 Mounting the Keypad
The keypad is designed for outdoor use. Choose a suitable location that is easily accessible and provides adequate protection from direct impact.
- Mark the desired mounting position on the wall or surface.
- Drill pilot holes for the mounting screws.
- Secure the keypad base to the surface using the provided screws and anchors.
- Ensure the keypad is firmly attached and level.
Figure 1: Front view of the Came Selt1Ndg Outdoor Keypad. The keypad features a black casing with a backlit numeric pad (0-9, *, #) for code entry. The "CAME" logo is visible at the top.
4.2 Wiring Connections
Refer to the wiring diagram provided with your specific access control unit for detailed connection instructions. The Selt1Ndg keypad typically connects to a control board (e.g., Came S0002 or R800 V2) using a multi-core cable.
- Power Supply: Connect the keypad to the appropriate power terminals on the control board.
- Data Lines: Connect the data output lines from the keypad to the corresponding input terminals on the control board.
- Backlight (Optional): If using a single keypad, the backlight functions automatically. For multiple keypads, a dedicated decoder board (e.g., R800 V2) may be required for backlight functionality.
- Ground: Ensure a proper ground connection.
Note: Incorrect wiring can damage the keypad or the control unit. Consult a professional if you are unsure about the wiring process.
5. Operating Instructions
5.1 Programming Access Codes
Programming of access codes is typically done via the connected control board, not directly on the keypad. Refer to your control board's manual for specific programming procedures. The keypad acts as an input device for these codes.
General Steps (may vary by control board):
- Access the programming mode on your control board.
- Enter the master code or administrator password.
- Follow the prompts to add new user codes.
- Enter the desired access code on the Selt1Ndg keypad when prompted by the control board.
- Confirm the code and exit programming mode.
5.2 Entering an Access Code
To gain access, enter your pre-programmed code followed by the '#' key (or 'E' on older systems, depending on control board configuration).
- The keypad backlight will illuminate when a key is pressed.
- Enter your numeric access code.
- Press the # key to confirm the entry.
- If the code is valid, the connected access control system will activate (e.g., open a gate or door).
6. Maintenance
The Came Selt1Ndg keypad requires minimal maintenance to ensure long-term performance.
- Cleaning: Periodically wipe the keypad surface with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Regularly inspect the keypad for any signs of physical damage, loose connections, or wear.
- Environmental Protection: While designed for outdoor use, avoid prolonged exposure to extreme weather conditions if possible.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Keypad not responding | No power; Loose connection; Faulty wiring. | Check power supply to the control board. Verify all wiring connections are secure. Consult wiring diagram. |
| Backlight not working | No power to backlight circuit; Multiple keypads without decoder. | Ensure power supply is adequate. If using multiple keypads, check if a decoder board (e.g., R800 V2) is required and correctly installed. |
| Access code not working | Incorrect code entered; Code not programmed; Control board issue. | Re-enter the code carefully. Verify the code is correctly programmed in the control board. Check the control board's status. |
| Keypad buttons are stiff or unresponsive | Dirt or debris under buttons; Physical damage. | Clean the keypad surface. If damage is present, contact support for repair or replacement. |
If troubleshooting steps do not resolve the issue, contact Came technical support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Came |
| Model Number | CMC806SL-0150 |
| Connectivity Technology | USB (Note: This specification from the source data may refer to an internal programming or diagnostic port, as operational keypads typically use wired connections to control units.) |
| Color | Black |
| Keypad Backlight | Single color backlight |
| Water Resistance Level | Not waterproof |
| Manufacturer | Came S.P.A. |
| Origin | Made in Italy |
Note on Water Resistance: While designed for outdoor installation, the keypad is specified as "Not waterproof." This indicates resistance to splashes and typical weather conditions, but it should not be submerged or exposed to high-pressure water jets. Proper installation and sealing are crucial for longevity in outdoor environments.
9. Warranty Information
Came products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Came website. Keep your proof of purchase for warranty claims.
10. Technical Support
For technical assistance, spare parts, or further information, please contact your local Came distributor or visit the official Came website:
- Website: www.came.com
- Contact: Refer to the "Contact Us" section on the website for regional support details.
