Introduction
Thank you for purchasing the HUSKY 2500 Lumen Portable LED Worklight. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new worklight. Please read all instructions carefully before use and retain this manual for future reference.
This worklight is designed to provide ample illumination for various tasks, featuring a durable, long-lasting LED bulb that never needs replacing. Its versatile design allows for use with or without the included stand, and an easy-grip handle facilitates transport when detached.
Safety Information
- Always ensure the worklight is placed on a stable, level surface to prevent tipping.
- Do not look directly into the light source when it is illuminated, as this may cause eye strain or damage.
- Keep the worklight away from flammable materials. Although the LED is cool to the touch, surrounding areas can still pose a fire hazard if not properly managed.
- Ensure the power cord is not damaged, pinched, or placed in areas where it could be a tripping hazard.
- This product is intended for indoor use or dry outdoor conditions. Do not expose to rain or moisture.
- Always unplug the worklight from the power source before cleaning or performing any maintenance.
- Do not attempt to modify or repair the worklight. Refer all servicing to qualified personnel.
Setup
- Unpacking: Carefully remove all components from the packaging. Verify that all parts are present: the LED worklight unit, and the stand assembly.
- Stand Assembly: The worklight typically comes pre-assembled with its stand. If the light head is detached, align the mounting holes on the light head with the brackets on the stand. Secure it using the provided knobs or screws, ensuring it is firmly attached and can pivot smoothly.
- Placement: Position the worklight on a flat, stable surface in the desired work area. Ensure there is adequate space around the light for ventilation and to prevent obstruction.
- Power Connection: Extend the 5 ft. power cord and plug the grounded plug into a standard 110V AC electrical outlet. Ensure the outlet is easily accessible.
Operating Instructions
- Powering On/Off: Locate the sealed power switch on the back of the worklight unit. Press the switch to the 'ON' position (usually indicated by 'I') to illuminate the LED. Press it to the 'OFF' position (usually indicated by 'O') to turn off the light.
- Adjusting Light Angle: The worklight head can be tilted and rotated on its stand to direct the light beam as needed. Loosen the adjustment knobs on the sides of the stand, position the light, and then tighten the knobs to secure it.
- Portable Use: The worklight can be detached from its stand for handheld or direct placement use. Simply loosen the securing knobs and lift the light unit from the stand. The integrated easy-grip handle allows for comfortable transport.
Maintenance
- Cleaning: Disconnect the worklight from the power source. Use a soft, dry cloth to wipe down the exterior surfaces. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Do not use abrasive cleaners or solvents.
- LED Bulb: The integrated LED bulb is designed for long-lasting performance and does not require replacement.
- Cord Care: Regularly inspect the power cord for any signs of damage, cuts, or fraying. If damage is found, discontinue use immediately and have the cord replaced by a qualified technician.
- Storage: When not in use, store the worklight in a clean, dry location, away from extreme temperatures and direct sunlight. Ensure the cord is neatly coiled to prevent tangling or damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Worklight does not turn on. | No power to the outlet. | Check the circuit breaker or try plugging into a different, known-working outlet. |
| Worklight does not turn on. | Power cord or plug is damaged. | Inspect the cord and plug for damage. If damaged, discontinue use and contact customer support. |
| Worklight does not turn on. | Power switch is faulty. | Ensure the switch is fully in the 'ON' position. If the issue persists, contact customer support. |
| Light output is dim or flickering. | Unstable power supply. | Ensure the worklight is connected to a stable power source. Avoid using with overloaded extension cords. |
If you encounter problems not listed above or if the suggested solutions do not resolve the issue, please contact Husky customer support for assistance.
Specifications
- Model Number: 819286010258
- Light Source Type: Integrated LED
- Lumen Output: 2500 Lumens (approximate, based on product title)
- Power Source: Corded Electric (110V)
- Voltage: 20 Volts (internal LED driver, operates on 110V AC input)
- Maximum Compatible Light Source Wattage: 15 Watts (LED equivalent)
- Material: Alloy Steel, Plastic, Glass (shade)
- Color: Black
- Item Weight: 3.4 Pounds
- Item Dimensions (L x W x H): 7.99" x 8.9" x 11.22"
- Cord Length: 5 ft. with grounded plug
- Mounting Type: Hand-Held / Stand
Warranty and Support
This HUSKY product is backed by a manufacturer's warranty. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your purchase or visit the official Husky website. Keep your proof of purchase for warranty claims.
For technical support, replacement parts, or general inquiries, please contact Husky customer service. Contact information can typically be found on the product packaging or the official Husky brand website.