SCHWAIGER LWH35535513 TV Wall Mount Instruction Manual

1. Introduction

This instruction manual provides detailed guidance for the safe and proper installation, operation, and maintenance of your SCHWAIGER LWH35535513 TV Wall Mount. This mount is designed to securely hold flat-panel televisions ranging from 32 to 75 inches in size, with a maximum weight capacity of 35 kg. Please read this manual thoroughly before beginning installation to ensure optimal performance and safety.

2. Safety Information

Important: Improper installation or use of this product can result in serious injury or damage. SCHWAIGER is not responsible for damage or injury caused by incorrect mounting, assembly, or use.

• Always ensure the mounting surface can safely support the combined weight of the mount and the television.
• Professional installation is recommended, especially for complex wall structures.
• Do not exceed the maximum weight capacity of 35 kg (77 lbs).
• Verify that all screws are securely tightened before use. Do not overtighten.
• Keep small parts away from children to prevent choking hazards.
• Wear appropriate safety gear during installation, including eye protection.
• If you have any doubts about the installation, consult a qualified professional.

3. Package Contents

Please check that all components are present and undamaged before installation. If any parts are missing or defective, contact SCHWAIGER customer support.

• Wall Plate Assembly
• TV Bracket Arms (x2 or x4 depending on VESA)
• Mounting Hardware Kit (various screws, washers, spacers, wall anchors)
• Instruction Manual

4. Setup and Installation

Follow these steps carefully for secure installation. Two people are recommended for TV mounting.

1. Prepare the Wall:

   Identify the desired mounting location. Use a stud finder to locate wooden studs if mounting on drywall, or ensure you are drilling into solid concrete/brick. Mark the drilling points for the wall plate using a pencil and a level.

2. Drill Pilot Holes:

   Drill pilot holes at the marked locations. The drill bit size will depend on your wall type and the anchors provided. For wooden studs, use a smaller bit; for concrete/brick, use a masonry bit and insert wall anchors.

3. Attach Wall Plate:

   Align the wall plate with the drilled holes and secure it to the wall using the appropriate screws and washers. Ensure the wall plate is level and firmly attached.

   

   Image 1: The SCHWAIGER LWH35535513 TV Wall Mount in its fully extended position, illustrating the wall-mounted arm and the TV attachment plate. This view helps visualize the overall structure before installation.

4. Attach TV Brackets to TV:

   Carefully place your TV face down on a soft, clean surface. Attach the TV bracket arms to the back of your television using the screws, washers, and spacers that match your TV's VESA mounting holes. Ensure the brackets are centered and securely fastened.

5. Mount TV to Wall Plate:

   With assistance, carefully lift the television and hook the TV bracket arms onto the wall plate. Ensure the TV is properly seated and engaged with the locking mechanism (if applicable). Some mounts have safety screws to prevent accidental dislodging; secure these if present.

5. Operating and Adjustments

This wall mount allows for flexible positioning of your television.

• Extension: The mount can extend your TV up to approximately 61 cm (24 inches) from the wall, providing various viewing angles.
• Swivel: To swivel the TV left or right, gently move the TV to the desired angle. The articulated arm allows for a wide range of horizontal movement.
• Tilt: To adjust the vertical tilt of the TV (up or down), you may need to loosen the tilt adjustment screws located on the TV mounting plate, adjust the angle, and then re-tighten the screws firmly. This mechanism ensures the TV remains at the set angle once adjusted.

Image 2: A side profile of the SCHWAIGER LWH35535513 TV Wall Mount, demonstrating its articulated arm for extension and the mechanism for tilt adjustment. This view highlights the range of motion.

6. Maintenance

Regular maintenance ensures the longevity and safety of your TV wall mount.

• Periodic Checks: Periodically check all screws and bolts to ensure they remain tight. Re-tighten if necessary, but do not overtighten.
• Cleaning: Clean the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
• Joints: The joints are designed for smooth operation. If movement becomes stiff, ensure no debris is obstructing the mechanism. Lubrication is generally not required for this type of mount.

7. Troubleshooting

If you encounter issues with your TV wall mount, refer to the following common solutions:

• Mount feels loose on the wall:

  Ensure all wall plate screws are securely tightened. If mounted into drywall, verify that the anchors are properly installed and holding firmly. If the issue persists, consult a professional to assess the wall structure.

• TV is not level:

  Check the level of the wall plate during installation. Some TV brackets allow for minor post-installation leveling adjustments. If not, you may need to re-adjust the TV brackets on the TV or the wall plate.
• Difficulty adjusting tilt or swivel:

  For tilt adjustments, ensure the tilt screws are sufficiently loosened before attempting to change the angle, then re-tighten. For swivel, ensure no cables are snagged or obstructing movement. The joints are designed to be firm to hold the TV's position.

8. Specifications

9. Warranty and Support

SCHWAIGER products are manufactured to high-quality standards. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official SCHWAIGER website.

For technical support, missing parts, or warranty claims, please contact SCHWAIGER customer service through their official website or the retailer where the product was purchased. Please have your model number (LWH35535513) and proof of purchase ready.