Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Good Earth Lighting 12-Inch Direct Wire LED Under Cabinet Light Fixture. Please read all instructions carefully before beginning installation and retain this manual for future reference.
This image shows the complete 12-inch LED under cabinet light fixture, ready for installation.
The Good Earth Lighting 12-Inch Direct Wire LED Under Cabinet Light Fixture is designed to provide efficient and smooth lighting for indoor applications, such as under cabinets. It features a frosted diffuser, an integrated on/off rocker switch, and is compatible with certain dimmers. This fixture is UL and ETL listed, ensuring compliance with safety standards.
The product packaging highlighting key features like 12-inch size, 355 lumens, and 6-year warranty.
Setup and Installation
Safety Information
- WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
- This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Use only UL/ETL listed wire connectors.
- Do not install in wet locations. For indoor use only.
Tools Required
- Phillips head screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Drill and drill bits (if mounting to wood/drywall)
- Pencil
- Measuring tape
Installation Steps
- Prepare for Installation: Turn off power at the circuit breaker or fuse box. Ensure the power is completely off before proceeding.
- Disassemble the Fixture: Carefully remove the lens cover. The housing separates from the mounting plate. Locate the small metal clips that hold the electrical housing in place. Gently pry these off to access the wiring compartment.
- Determine Mounting Location: Choose a suitable location under your cabinet. Ensure there is enough space for the fixture and access for wiring. Mark the mounting screw locations using a pencil.
- Mount the Fixture Base: Secure the fixture's mounting plate to the marked location using appropriate screws (included). Ensure it is firmly attached.
- Wire the Fixture:
- Feed the household electrical wires through the knockout hole in the fixture's base.
- Connect the black (hot) wire from the fixture to the black (hot) wire from the household supply using a wire nut.
- Connect the white (neutral) wire from the fixture to the white (neutral) wire from the household supply using a wire nut.
- Connect the green (ground) wire from the fixture to the bare copper (ground) wire from the household supply using a wire nut.
- Ensure all connections are secure and insulated with electrical tape if necessary. Carefully tuck all wires into the wiring compartment.
- Reassemble the Fixture: Reattach the electrical housing to the mounting plate, ensuring the metal clips engage securely. Replace the lens cover.
- Restore Power: Turn the power back on at the circuit breaker or fuse box. Test the light fixture using the integrated rocker switch.
Operating Instructions
Turning the Light On/Off
The fixture is equipped with an easily accessible on/off rocker switch located on the side or front of the unit. Press the side marked 'I' to turn the light ON, and the side marked 'O' to turn the light OFF.
A detailed view of the integrated rocker switch, used to control the light fixture.
Dimming Functionality
This LED fixture can be used with compatible dimmers. For optimal performance and to avoid flickering or damage, ensure that any dimmer used is specifically rated for LED lighting. Consult the dimmer manufacturer's instructions for proper installation and operation.
Maintenance
Cleaning
To clean the fixture, ensure the power is turned off at the circuit breaker. Use a soft, dry, or slightly damp cloth to wipe the exterior surfaces. Do not use abrasive cleaners, solvents, or polishes, as these can damage the finish or electrical components.
LED Light Source
This fixture utilizes an integrated LED light source designed for long life (approximately 50,000 hours). The LEDs are not replaceable. If the light source fails, the entire fixture should be replaced.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Loose wiring connection. Faulty switch. | Check circuit breaker/fuse. Ensure all wire connections are secure (power off first). Test the rocker switch. |
| Light flickers or dims unexpectedly. | Incompatible dimmer switch. Loose wiring. | Ensure dimmer is LED-compatible. Check all wiring connections (power off first). |
| Light is too dim. | Dimmer set too low. Expected brightness for the fixture. | Adjust dimmer to a higher setting. Verify the lumen output in specifications matches expectations. |
| Humming noise from fixture. | Incompatible dimmer. | Replace dimmer with an LED-compatible model. |
Specifications
- Brand: Good Earth Lighting
- Model Number: UC1061-WH1-12LF0-G
- Size: 12-Inch
- Light Source: LED (Integrated)
- Wattage: 6 watts
- Light Color: White
- Control Method: Remote (compatible with remote dimmers)
- Switch Type: Rocker (on-fixture)
- Power Source: Corded Electric (Direct Wire)
- Material: Glass (diffuser)
- Finish: Matte
- Installation Type: Surface Mount (Under Cabinet)
- Indoor/Outdoor Usage: Indoor Only
- Water Resistance Level: Not Water Resistant
- Average Life Expectancy: 50,000 hours
- Certifications: UL Listed, ETL Listed
- UPC: 755284017410
Warranty Information
This Good Earth Lighting fixture is covered by a 6-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the warranty documentation included with your product or contact customer support.
Customer Support
If you have any questions, require assistance with installation, or need to report a problem with your Good Earth Lighting fixture, please contact Good Earth Lighting customer service. Contact information can typically be found on the product packaging or the official Good Earth Lighting website.
Website: www.goodearthlighting.com (Please check the official website for the most current contact details.)
