Product Overview
The Hyper Tough 6-Outlet Surge Protector is designed to safeguard your electronic devices from power surges and spikes. This unit features six grounded outlets, an integrated on/off switch with a built-in circuit breaker, and provides 500 joules of surge protection. It is suitable for indoor use only and comes with a 2.5-foot (76 cm) power cord.
Product Visual
This image displays the Hyper Tough 6-Outlet Surge Protector in its packaging. It highlights the six grounded outlets, the on/off switch with a built-in circuit breaker, and key specifications such as 14-gauge wire, 500-joule protection, and a 2.5-foot cord. The packaging also indicates a 2-year limited warranty and a $50,000 connected equipment warranty.
Setup Instructions
- Unpack the Surge Protector: Carefully remove the surge protector from its packaging.
- Choose a Location: Select a dry, indoor location near the electronic devices you wish to protect. Ensure the location is free from moisture and excessive heat.
- Plug into Wall Outlet: Insert the surge protector's plug firmly into a standard 120V AC grounded wall outlet. Do not plug into another surge protector or extension cord.
- Connect Devices: Plug your electronic devices into the six grounded outlets on the surge protector. Ensure all device plugs are fully inserted.
- Power On: Press the on/off switch to the "ON" position. The indicator light (if present) should illuminate, signifying that the surge protector is active and providing protection.
Important Safety Note: This surge protector is designed for indoor use only. Do not use in wet environments or near water sources.
Operating the Surge Protector
The Hyper Tough 6-Outlet Surge Protector is simple to operate:
- Power On/Off: The large red switch on the unit controls power to all six outlets. Press the switch to the "ON" position to supply power to connected devices. Press it again to the "OFF" position to cut power.
- Circuit Breaker: This surge protector features a built-in circuit breaker. In the event of an overload, the circuit breaker will automatically trip to protect your devices and the surge protector itself. If this occurs, the power switch will likely pop out or move to the "OFF" position.
Care and Maintenance
- Cleaning: Disconnect the surge protector from the wall outlet before cleaning. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or abrasive chemicals.
- Storage: When not in use, store the surge protector in a cool, dry place away from direct sunlight and moisture.
- Inspection: Periodically inspect the power cord and the surge protector for any signs of damage, such as frayed wires or cracked casing. If damage is found, discontinue use immediately and replace the unit.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to connected devices. | The surge protector's power switch is OFF or the circuit breaker has tripped. | Ensure the power switch is in the "ON" position. If the circuit breaker tripped (switch is popped out), unplug some devices, then press the switch back to "ON" to reset. |
| Surge protector feels warm. | Normal operation under load, or excessive load. | A slight warmth is normal. If it feels excessively hot, unplug devices and reduce the total load. Ensure proper ventilation. |
| Devices are still damaged after a surge. | Surge was too powerful, or surge protection components have degraded over time. | While surge protectors offer protection, extremely powerful surges can still cause damage. Surge protectors have a finite lifespan for protection; consider replacing older units. Refer to warranty information for connected equipment claims. |
Technical Specifications
- Model: 6-Outlet 2.5FT Surge Protector
- Outlets: 6 Grounded Outlets
- Voltage: 120 Volts AC
- Max Amperage: 15 Amps
- Wire Gauge: 14 AWG
- Surge Protection: 500 Joules
- Cord Length: 2.5 feet (76 cm)
- Special Feature: Surge Protection, Built-in Circuit Breaker
- Dimensions (Approx.): 9 x 3 x 1 inches (Package Dimensions)
- Weight (Approx.): 4.99 pounds (Item Weight)
- Usage: Indoor Use Only
Warranty Information
This Hyper Tough Surge Protector comes with a 2-Year Limited Warranty. This warranty covers defects in materials and workmanship under normal use.
Additionally, the product includes a $50,000 Connected Equipment Warranty. This warranty provides coverage for equipment properly connected to the surge protector that is damaged by a power surge while the surge protector is functioning correctly. Please refer to the original product packaging or manufacturer's website for full terms, conditions, and claim procedures for both warranties.
Customer Support
For technical assistance, warranty claims, or general inquiries regarding your Hyper Tough 6-Outlet Surge Protector, please contact Hyper Tough customer service. Contact information can typically be found on the product packaging or the official Hyper Tough website.
When contacting support, please have your product model number (6-Outlet 2.5FT Surge Protector) and purchase information readily available.