1. Introduction
This manual provides essential instructions for the safe and effective operation, installation, maintenance, and troubleshooting of your Ironton 12 Volt Electric Trailer Jack. Designed for A-frame trailers, this jack offers a 3,500-lb. lifting capacity and a height range of 9 inches to 31.5 inches. Please read this manual thoroughly before use and retain it for future reference.
2. Safety Information
WARNING: Failure to follow these safety instructions may result in serious injury or property damage.
- Always ensure the trailer is on a level surface and properly chocked before operating the jack.
- Do not exceed the maximum lifting capacity of 3,500 lbs.
- Keep hands and feet clear of moving parts during operation.
- Ensure all electrical connections are secure and free from corrosion.
- Disconnect power before performing any maintenance or adjustments.
- Use the manual crank override only when electrical power is unavailable.
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).
3. Product Overview and Components
The Ironton Electric Trailer Jack is designed for ease of use and durability. Key features include:
- 3,500-lb. lift capacity for various trailers.
- Height range of 9in. to 31 1/2in. (ground to center of mounting point).
- Fits standard 2 1/4in. mounting holes.
- Adjustable, oversized foot pad (7-1/8in.) to prevent ground divots and enhance stability.
- Weather-sealed switch for reliable operation in various conditions.
- Manual crank override for use without electrical power.
Figure 3.1: Front view of the Ironton 12 Volt Electric Trailer Jack.
Figure 3.2: The electric trailer jack highlighting its 3,500-lb. lift capacity, suitable for heavy trailers.
Figure 3.3: Close-up of the 7-1/8 inch foot pad, designed for stability and preventing ground divots.
4. Setup and Installation
Follow these steps to properly install your electric trailer jack:
- Preparation: Ensure the trailer is disconnected from the towing vehicle and supported by appropriate jack stands. The area should be level and stable.
- Remove Old Jack (if applicable): If replacing an existing jack, remove the old unit by unbolting it from the A-frame coupler.
- Positioning: Insert the new Ironton Electric Trailer Jack into the 2-1/4 inch mounting hole on the trailer's A-frame coupler.
- Secure Mounting: Align the mounting holes and secure the jack using three (3) machine bolts (not included) and lock nuts. Ensure all fasteners are tightened to the manufacturer's specifications.
- Electrical Connection: Connect the jack's power wire to a 12-volt power source (typically the trailer battery). Ensure the connection is secure, clean, and protected from weather.
- Foot Pad Adjustment: Adjust the oversized foot pad to the desired height, ensuring it is securely pinned in place.
Figure 4.1: The manual crank override mechanism, useful during installation or power outages.
5. Operating Instructions
Operating your Ironton Electric Trailer Jack is straightforward:
- Power On: Ensure the jack is connected to a 12-volt power source.
- Extend/Retract: Use the weather-sealed switch to extend or retract the jack. Press the appropriate button to raise or lower the trailer.
- Leveling: Adjust the jack until the trailer is level or at the desired height for hitching or unhitching.
- Manual Override: In case of power failure, remove the rubber cap on top of the jack housing to access the manual crank. Insert the provided crank handle and turn it clockwise to lower or counter-clockwise to raise the jack.
Figure 5.1: The weather-sealed switch, designed for durability in various environmental conditions.
Video 5.1: Demonstration of the Ironton 12 Volt Electric Trailer Jack in operation, showing its smooth extension and retraction. This video illustrates the product's functionality and ease of use for trailer leveling and hitching.
6. Maintenance
Regular maintenance ensures the longevity and reliable performance of your electric trailer jack:
- Lubrication: Periodically lubricate the inner and outer tubes of the jack with a suitable grease to ensure smooth operation and prevent corrosion.
- Electrical Connections: Inspect all electrical connections for corrosion or damage. Clean and tighten as necessary.
- Foot Pad: Check the foot pad for wear or damage. Replace if necessary.
- General Inspection: Regularly inspect the entire jack for any signs of damage, loose fasteners, or unusual wear. Address any issues promptly.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Jack does not operate electrically. | No power, loose connection, blown fuse, faulty switch. | Check battery connection, inspect fuse, test switch, ensure power source is active. Use manual override if necessary. |
| Jack operates slowly or with difficulty. | Low battery voltage, insufficient lubrication, excessive load. | Charge battery, lubricate jack tubes, reduce load (ensure within 3500-lb capacity). |
| Jack makes unusual noises. | Lack of lubrication, internal damage. | Lubricate moving parts. If noise persists, discontinue use and contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Ironton |
| Model Number | 3405855 |
| Lift Capacity | 3500 lbs. |
| Voltage | 12 Volt |
| Height Range | 9 in. to 31.5 in. |
| Mounting Hole Size | 2-1/4 in. |
| Foot Pad Size | 7-1/8 in. |
| Amperage (Full-Load) | 23-25 Amp |
| Item Weight | 23.8 pounds |
| Package Dimensions | 32 x 8 x 8 inches |
9. Warranty and Support
For warranty information or technical support regarding your Ironton 12 Volt Electric Trailer Jack, please refer to the official Ironton website or contact their customer service department. Keep your purchase receipt for warranty claims.
You can visit the Ironton Store on Amazon for more information or to explore other products.
