Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Armacost Lighting Wireless Touchpad, Model 523120. This wireless touchpad is designed to provide remote on/off control and dimming functionality for compatible Armacost Lighting 2-in-1 LED Dimmers, specifically model 511120, using radio frequency (RF) technology.
Safety Information
Please read all instructions carefully before installation and use. Failure to follow these instructions may result in electrical shock, fire, or other hazards.
- Ensure power is disconnected before performing any installation or maintenance.
- This device is intended for indoor use only.
- Do not expose the touchpad to moisture or extreme temperatures.
- Use only the specified battery type (12-volt alkaline, 27A).
- Keep batteries out of reach of children.
- Consult a qualified electrician if you are unsure about any part of the installation process.
Package Contents
Verify that all components are present before beginning installation:
- Wireless Touchpad
- Wall Plate
- Mounting Screws
- Drywall Anchors
- One 12-volt Alkaline Battery (27A)
Figure 1: Wireless Touchpad components, showing the touchpad, wall plate, mounting bracket, and various screws and anchors.
Setup
Battery Installation
The wireless touchpad requires one 12-volt alkaline battery (27A) for operation. Follow these steps to install the battery:
- Carefully remove the back cover of the touchpad.
- Insert the 12-volt alkaline battery (27A) into the battery compartment, ensuring correct polarity (+/-).
- Replace the back cover securely.
Figure 2: Wireless Touchpad showing the battery compartment with a 12-volt alkaline battery (27A) installed.
Mounting Options
The touchpad can be mounted in two ways:
- Surface Mount: Use the provided mounting screws and drywall anchors to attach the mounting bracket directly to a wall surface. The touchpad then snaps into the bracket, and the wall plate covers it.
- Standard Switch Plate Array: The touchpad can be installed into a standard switch plate array that uses a rectangular opening, replacing a traditional switch.
Pairing with a 2-in-1 LED Dimmer
The wireless touchpad must be paired with a compatible Armacost Lighting 2-in-1 LED Dimmer (Model 511120) to function. Multiple touchpad/receiver sets can control different lighting zones without interference. This touchpad can also be paired to control and synchronize multiple dimmer receivers in the same area.
To pair the touchpad with your dimmer:
- Ensure the 2-in-1 LED Dimmer (Model 511120) is powered on and connected to your LED lighting.
- On the 2-in-1 LED Dimmer, locate the pairing button (refer to the dimmer's manual for exact location). Press and hold the pairing button for approximately 3 seconds until the connected LED lights flash or the dimmer's indicator light blinks.
- Within 10 seconds of activating the dimmer's pairing mode, press and hold the "On" (power) button on the wireless touchpad for approximately 3 seconds.
- The connected LED lights should flash again, or the dimmer's indicator light should stop blinking, confirming successful pairing.
- Test the touchpad's functionality by pressing the On/Off and dimming buttons.
Figure 3: Wireless Touchpad shown with a compatible 2-in-1 LED Dimmer module, ready for pairing.
Operating Instructions
The wireless touchpad provides intuitive control over your paired LED lighting system.
Figure 4: Close-up of the Wireless Touchpad buttons.
Power On/Off
- To turn the lights ON, press the ⏻ (Power) button once.
- To turn the lights OFF, press the ⏻ (Power) button once.
Dimming Control
- To increase brightness, press the ▲ (Up Arrow) button. Hold the button for continuous dimming.
- To decrease brightness, press the ▼ (Down Arrow) button. Hold the button for continuous dimming.
The touchpad offers a smooth fade-up and fade-down effect when turning lights on or off.
Maintenance
Battery Replacement
The wireless touchpad is powered by a 12-volt alkaline battery (27A). If the touchpad becomes unresponsive or its range decreases, the battery may need replacement.
- Carefully remove the back cover of the touchpad.
- Remove the old 27A battery from its compartment.
- Insert a new 12-volt alkaline battery (27A), ensuring correct polarity (+/-).
- Replace the back cover securely.
- Dispose of the old battery responsibly according to local regulations.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Touchpad is unresponsive. | Low or dead battery. | Replace the 12-volt alkaline battery (27A). |
| Lights do not respond after pairing attempt. | Incorrect pairing procedure or incompatible dimmer. | Ensure you are pairing with Armacost Lighting 2-in-1 dimmer model 511120. Repeat the pairing steps carefully. Ensure the dimmer is powered on. |
| Reduced signal range. | Low battery or excessive interference. | Replace the battery. While the touchpad works through walls, extreme obstructions or other strong RF signals might reduce range. |
| Multiple dimmers not synchronizing correctly. | Pairing issue with multiple receivers. | Ensure each dimmer is correctly paired. If controlling multiple dimmers with one touchpad, ensure they are all in pairing mode simultaneously before pressing the touchpad's power button. |
Specifications
- Model Number: 523120
- Part Number: DIM14REM
- Brand: Armacost Lighting
- Power Source: 1 x 12-volt Alkaline Battery (27A)
- Signal Range: Up to 100 ft (line of sight not required; works through interior walls and doors)
- Compatibility: Armacost Lighting 2-in-1 LED Dimmer Model 511120
- Mounting Type: Wall Mount (surface or standard switch plate array)
- Switch Style: Push Button
- Color: White
- Product Dimensions: 5 x 3 x 1 inches
- Item Weight: 3.2 ounces
- Certification: UL
Warranty and Support
For warranty information or technical support, please contact Armacost Lighting customer service. Refer to the product packaging or the official Armacost Lighting website for current contact details and warranty terms.
Website: www.armacostlighting.com
