Product Overview
The Flashpoint R2 Pro O wireless flash trigger is a dedicated light master designed for Panasonic and Olympus cameras, providing comprehensive control over the Flashpoint R2 wireless system. This transmitter allows photographers to manage multiple flash units, including speedlights, strobes, and monolights, directly from their camera. Its intuitive interface and advanced features like TCM (TTL Converted to Manual) ensure precise and efficient lighting control for various photographic scenarios.
Setup Guide
1. Unpacking and Initial Inspection
Carefully remove the Flashpoint R2 Pro Transmitter from its packaging. Inspect the device for any signs of damage during transit. Ensure all included components, such as the instruction manual and warranty information, are present.
2. Battery Installation
- Locate the battery compartment on the rear of the transmitter.
- Slide the battery compartment cover open.
- Insert two AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
- Close the battery compartment cover securely.
3. Mounting to Camera
- Ensure your camera is powered off.
- Slide the hot shoe foot of the R2 Pro Transmitter into your camera's hot shoe mount.
- Tighten the locking ring on the transmitter's hot shoe foot until it is firmly secured to the camera. Do not overtighten.
Operating Instructions
1. Powering On/Off
To power on the transmitter, slide the 'ON/OFF' switch located on the side of the unit to the 'ON' position. The LCD screen will illuminate. To power off, slide the switch back to 'OFF'.
2. Navigating the Interface
The R2 Pro features a large dot matrix LCD screen and dedicated buttons for easy navigation and control. Use the dial and 'SET' button to adjust values and confirm selections. The 'MODE', 'MENU', and group buttons (A, B, C, D, E) provide direct access to various settings.
3. Basic Flash Control (TTL/Manual)
- TTL Mode: Press the 'MODE' button to cycle through modes until 'TTL' is displayed for the desired group. The transmitter will automatically adjust flash power based on camera metering.
- Manual Mode: Press the 'MODE' button to select 'M' for manual control. Use the dial to adjust the flash power output (e.g., 1/1 to 1/256).
4. Group Management
The R2 Pro supports up to 5 groups (A, B, C, D, E). Press the corresponding group button to select it, then use the 'MODE' button and dial to adjust its settings independently. The LCD screen displays all 5 groups simultaneously for quick overview.
5. High-Speed Sync (HSS)
To enable High-Speed Sync, ensure your camera and flash units support HSS. The transmitter will automatically activate HSS when the camera's shutter speed exceeds its maximum flash sync speed (e.g., 1/250s).
6. TCM Function
The TCM (TTL Converted to Manual) function allows you to take a TTL reading and then convert that power output to a manual setting. This is useful for maintaining consistent exposure when moving from TTL to manual mode. Press the 'TCM' button to activate this feature.
7. Channel Selection
The transmitter supports 32 channels to prevent interference. To change the channel, press the 'CH/Zm' button and use the dial to select the desired channel. Ensure your flash units are set to the same channel as the transmitter.
Maintenance
1. Cleaning
Use a soft, dry cloth to clean the exterior of the transmitter. For stubborn marks, a slightly damp cloth with mild soap can be used, followed by a dry cloth. Do not use harsh chemicals or abrasive materials. Keep the hot shoe contacts clean and free of debris.
2. Storage
When not in use for extended periods, remove the batteries to prevent leakage. Store the transmitter in a cool, dry place, away from direct sunlight and extreme temperatures. Use the original packaging or a protective case to prevent dust and physical damage.
3. Firmware Updates
Periodically check the Flashpoint official website for available firmware updates. Firmware updates can improve performance, add new features, or resolve bugs. Follow the instructions provided with the firmware download carefully to perform the update via the USB-C port.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Transmitter does not power on. | Low or dead batteries; incorrect battery installation. | Replace batteries with fresh ones; ensure correct polarity. |
| Flash units not firing. | Incorrect channel; flash units not powered on; transmitter not securely mounted. | Verify transmitter and flash units are on the same channel; power on all flash units; ensure transmitter is firmly attached to camera hot shoe. |
| Inconsistent flash exposure. | Interference from other devices; incorrect TTL/Manual settings. | Change to a different channel; re-evaluate TTL exposure compensation or manual power settings. |
| LCD screen is dim or unresponsive. | Low battery; extreme temperature. | Replace batteries; allow unit to return to normal operating temperature. |
Technical Specifications
| Feature | Specification |
|---|---|
| Product Dimensions | 4.9 x 4.8 x 2.5 inches |
| Item Weight | 3.2 ounces |
| Model Number | R2 Remote |
| Compatible Mountings | Panasonic, Olympus |
| Wireless Frequency | 2.4GHz |
| Channels | 32 |
| Groups | 5 (A, B, C, D, E) |
| Sync Modes | High-Speed Sync (HSS), First Curtain Sync, Second Curtain Sync |
| Power Source | 2 x AA Batteries |
Warranty and Support
The Flashpoint R2 Pro Transmitter comes with a Flashpoint 1-Year USA Warranty. This warranty covers manufacturing defects and ensures the product's quality and performance for one year from the date of purchase.
For technical support, troubleshooting assistance, or warranty claims, please contact Flashpoint customer service. Refer to the contact information provided in your product packaging or visit the official Flashpoint website for the most up-to-date support resources.