Olide Swing Door Automatic Opening System Olide-120B Instruction Manual

1. Safety Information

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or improper operation of the device. Keep this manual for future reference.

• Ensure all electrical connections are performed by a qualified electrician and comply with local electrical codes.
• Disconnect power before performing any maintenance or adjustments.
• Do not allow children to play with the automatic door system or its controls.
• Regularly inspect the system for any signs of wear, damage, or loose components.
• This device is designed for swing doors. Do not attempt to use it on other door types.

2. Product Overview

The Olide Swing Door Automatic Opening System, model Olide-120B, is designed to provide convenient and accessible automatic operation for swing doors. It is suitable for various applications, including residential and commercial settings, assisting individuals with mobility challenges.

Key Components:

• Automatic Door Opener Unit (Motor and Controller)
• Swing Arm (Pull or Push type)
• Remote Controls
• Hand Induction Switches
• Power Cable
• Adjustment Tool (Hex keys)

3. Setup and Installation

The Olide-120B system is designed for screw mounting. Proper installation is crucial for safe and reliable operation. It is recommended that installation be performed by a professional.

3.1 Pre-Installation Checks

• Ensure the door width does not exceed 1200mm.
• Verify the door weight is within the maximum limit of 120kg.
• Confirm a stable power supply of 110V/AC, 50/60Hz is available at the installation site.
• Determine the door's swing direction (inward or outward) to select the appropriate arm configuration (pull arm or push arm).

3.2 Mounting the Main Unit

Mount the main opener unit securely above the door frame using appropriate screws and anchors. Ensure it is level and aligned with the door.

3.3 Arm Installation

Attach the swing arm to the main unit and the door. The type of arm (pull or push) depends on whether the door opens inward or outward.

3.4 Electrical Connections

Connect the power supply and control devices (remote receiver, hand induction switches) to the controller unit as per the wiring diagram provided in the detailed installation guide (not included in this manual). Ensure all connections are secure and insulated.

3.5 Initial Adjustments

After installation, use the handheld programmer to set initial parameters:

• Opening/Closing Speed: Adjust the door's movement speed.
• Manual Push Function: Enable or disable the ability to manually push the door open.
• Opening Direction: Configure for single-direction or bi-directional opening.
• Hold-Open Time: Set how long the door remains open after activation.

4. Operating Instructions

The Olide-120B system can be operated using remote controls or hand induction switches.

4.1 Using Remote Controls

Press the designated button on the remote control to activate the door. The door will open, remain open for the set hold-open time, and then close automatically.

4.2 Using Hand Induction Switches

Wave your hand over the sensor area of the hand induction switch to activate the door. The door will open and close according to the programmed settings.

4.3 Adjusting Parameters

The handheld programmer (refer to Figure 3.2) allows for fine-tuning of operational parameters such as opening/closing speed (250-450mm/s), opening direction (both-way or one-way), and hold-open time. Consult the detailed programming guide for specific instructions on using the programmer.

5. Maintenance

Regular maintenance ensures the longevity and safe operation of your Olide-120B system.

• Monthly Inspection: Check all mounting screws and connections for tightness. Ensure the swing arm moves freely without obstruction.
• Cleaning: Keep the main unit and sensors clean and free from dust and debris. Use a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Lubrication: Periodically check the moving parts of the swing arm for smooth operation. Apply a small amount of silicone-based lubricant if necessary, avoiding electrical components.
• Sensor Check: Test the hand induction switches and any other sensors regularly to ensure they respond correctly.

6. Troubleshooting

If you encounter issues with your Olide-120B system, refer to the following common problems and solutions:

• Door not opening/closing: Check power supply, ensure all cables are securely connected, and verify remote control batteries.
• Door moves erratically: Inspect the swing arm for obstructions or damage. Check parameter settings with the handheld programmer.
• Sensors not responding: Clean the sensor surface. Ensure there are no objects blocking the sensor's field.
• Unusual noises: Inspect moving parts for wear or misalignment. Lubricate if necessary. If the noise persists, contact support.

For complex issues not covered here, please contact Olide customer support.

7. Specifications

Detailed technical specifications for the Olide Swing Door Automatic Opening System Olide-120B:

8. Warranty and Support

8.1 Warranty Information

The Olide Swing Door Automatic Opening System Olide-120B comes with a 5-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

8.2 Customer Support

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Olide customer support through your retailer or the official Olide website. Provide your model number (Olide-120B) and a detailed description of the issue when contacting support.