Product Overview
The Luceco Solar LED Guardian Wall Light is a robust and high-quality outdoor lighting solution designed for easy, wire-free installation. It features a PIR motion sensor and a solar panel for energy efficiency. This light is ideal for illuminating and securing outdoor areas such as terraces, balconies, driveways, and gardens.
Front view of the Luceco Solar LED Guardian Wall Light, showing the solar panels and the main LED light panel.
Key Features
- Color Temperature: 4000K (Natural White)
- Power Consumption: 6.8 watts
- Luminous Flux: 800 lumens
- Three Operating Modes: Night light, Night light + motion detection, Motion detection only
- Battery: 4000 mAh Lithium-ion battery included
- IP Rating: IP54 rated for outdoor use
- Integrated PIR motion sensor
- Simple push-button switch for mode selection
Setup and Installation
The Luceco Solar LED Guardian Wall Light is designed for simple and quick installation without the need for mains wiring, making it ideal for locations where electrical outlets are not readily available. Ensure the installation location receives ample direct sunlight throughout the day for optimal charging.
Mounting
- Choose a suitable wall or surface for mounting, ideally between 2 to 3 meters high for optimal motion detection and illumination coverage.
- Mark the positions for the mounting screws using the light's mounting holes as a template.
- Drill pilot holes if necessary and insert appropriate wall anchors.
- Secure the light to the wall using screws, ensuring it is firmly attached.
Diagram showing the dimensions of the Luceco Solar LED Guardian Wall Light: 270mm length, 220mm height, 110mm depth.
Luceco Solar LED Guardian Wall Light mounted on the exterior of a garden shed, providing illumination at night.
Operating Instructions
The Luceco Solar LED Guardian Wall Light features a push-button switch on the back to select between three distinct operating modes. The light charges automatically during the day via its solar panel.
Charging
The integrated solar panel charges the internal 4000 mAh Lithium-ion battery during daylight hours. Ensure the solar panel is clean and free from obstructions to maximize charging efficiency.
Operating Modes
Press the button on the back of the unit to cycle through the following modes:
- Mode 1 (Beacon Mode): The light turns on at a low beacon level at dusk and remains on for 5 hours, then turns off.
- Mode 2 (Beacon + Detection Mode): The light stays at a low beacon level at dusk. Upon motion detection, it illuminates at full power (800 lm) for 20 seconds, then returns to beacon mode if no further motion is detected.
- Mode 3 (Detection Only Mode): The light remains off at dusk. Upon motion detection, it illuminates at full power (800 lm) for 30 seconds, then turns off if no further motion is detected.
Diagram illustrating the illumination range and height for the Luceco Solar LED Guardian Wall Light, showing optimal mounting height of 2-3m and a detection distance of 4m.
Maintenance
To ensure optimal performance and longevity of your Luceco Solar LED Guardian Wall Light, follow these maintenance guidelines:
- Cleaning: Regularly wipe the solar panel and light surface with a soft, damp cloth to remove dust, dirt, and debris. A clean solar panel ensures efficient charging. Avoid abrasive cleaners or solvents.
- Battery Care: The integrated Lithium-ion battery is designed for long-term use. For best performance, ensure the light receives sufficient sunlight for charging daily. In prolonged periods of low sunlight, the light's performance may be reduced.
- Inspection: Periodically check the mounting screws and the light's housing for any signs of wear or damage. Ensure the light remains securely mounted.
Troubleshooting
If your Luceco Solar LED Guardian Wall Light is not functioning as expected, refer to the following troubleshooting table:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at night | Insufficient solar charge Mode not selected correctly Battery issue | Ensure the solar panel is clean and exposed to direct sunlight for at least 6-8 hours daily. Relocate if necessary. Press the mode selection button on the back to cycle through the operating modes. The battery may be depleted or at the end of its life. While not user-replaceable, ensure proper charging conditions. |
| Light stays on constantly or does not turn off | Continuous motion detected Sensor malfunction | Ensure the motion sensor is not obstructed or detecting constant movement from trees, pets, or passing vehicles. If the issue persists after checking for continuous motion, the sensor may be faulty. |
| Light is dim or flickers | Low battery charge Dirty solar panel | Allow the light to charge fully in direct sunlight. Clean the solar panel thoroughly. |
| Motion sensor not detecting | Obstruction in sensor's path Incorrect mounting height/angle Extreme temperatures | Ensure the sensor is clear of obstructions. Adjust the mounting height (optimal 2-3m) and angle to ensure the sensor covers the desired area. Performance may be affected by extremely low or high temperatures. |
Technical Specifications
Detailed specifications for the Luceco Solar LED Guardian Wall Light:
| Feature | Specification |
|---|---|
| Brand | Luceco |
| Model Number | LEXS80W40-01 |
| Product Dimensions | 27 x 27 x 22 cm |
| Item Weight | 790 grams |
| Power Consumption | 6.8 Watts |
| Luminous Flux | 800 lumens |
| Color Temperature | 4000 Kelvin (Natural White) |
| Color Rendering Index (CRI) | 80 |
| Battery Type | 1 Lithium-ion (included) |
| Battery Capacity | 4000 mAh |
| Voltage | 3.7 Volts |
| IP Rating | IP54 |
| Material | Metal Acrylonitrile Butadiene Styrene (ABS) |
| Shade Material | Aluminum |
| Finish Type | Powder coating |
| Number of Bulbs | 1 (LED) |
| Included Components | Motion detector |
| Specific Uses | Outdoor use |
| Special Features | Robust, Solar powered |
| Switch Style | Push button |
| Installation Type | Wall mount |
| Country of Origin | France |
Warranty and Support
Warranty Information
Information regarding specific warranty terms and conditions for the Luceco Solar LED Guardian Wall Light (Model LEXS80W40-01) is not provided in the product details. Please refer to your point of purchase or the manufacturer's official website for any available warranty information.
Customer Support
For technical assistance or further inquiries, please contact Luceco customer support through their official channels. Contact details are typically available on the manufacturer's website or product packaging.
