1. Introduction and Overview
Thank you for choosing the Bristan Round Push Basin Waste Slotted Chrome (Model W BASIN08 C). This high-quality plumbing accessory is designed to provide reliable and efficient drainage for your basin. Crafted with robust materials, it ensures durability and a long service life.
Key features of this product include:
- Solid brass construction for enhanced strength and corrosion resistance.
- Metal back nut for added durability and secure installation.
- Chrome finish for a modern aesthetic and easy cleaning.
2. Safety Information
Please read all instructions carefully before installation and use. Failure to follow these instructions may result in property damage or injury.
- Always turn off the water supply before attempting any plumbing work.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Keep small parts away from children to prevent choking hazards.
3. Package Contents
Verify that all components are present before beginning installation:
- 1 x Basin Waste Unit
- 1 x Fixing Kit (washers, nuts)
- Installation Instructions
Image: The Bristan Round Push Basin Waste Slotted Chrome unit, showing its polished chrome finish and push-button mechanism.
4. Setup and Installation
This section provides general guidance for installing the basin waste. Specific basin designs may require slight variations.
- Prepare the Basin: Ensure the basin's waste hole is clean and free from debris.
- Apply Sealant: Apply a bead of plumber's putty or silicone sealant around the underside of the waste flange (the top part that sits inside the basin). This helps create a watertight seal.
- Insert Waste Unit: Insert the waste unit through the basin hole from the top. Ensure the flange is centered and seated correctly.
- Secure from Below: From underneath the basin, slide the rubber washer, then the plastic washer, and finally the metal back nut onto the threaded body of the waste.
- Tighten: Hand-tighten the metal back nut, then use a suitable wrench to gently tighten it further. Do not overtighten, as this can damage the basin or the waste unit.
- Connect to Trap: Connect the waste unit to your basin trap (not included) according to the trap manufacturer's instructions. Ensure all connections are secure and watertight.
- Test for Leaks: Turn on the water supply and fill the basin. Check thoroughly for any leaks around the waste unit and trap connections. Tighten connections as necessary.
Image: Technical drawing illustrating the dimensions (in mm) of the Bristan Round Push Basin Waste, including diameters and heights.
5. Operating Instructions
The Bristan Round Push Basin Waste features a simple push-button mechanism for operation:
- To Close the Waste: Gently press the center of the waste plug. It will click into the closed position, retaining water in the basin.
- To Open the Waste: Gently press the center of the waste plug again. It will click into the open position, allowing water to drain from the basin.
6. Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your basin waste.
- Cleaning: Clean the chrome finish regularly with a soft cloth and mild soapy water. Avoid abrasive cleaners, scouring pads, or chemical agents, as these can damage the finish.
- Removing Debris: Periodically, the top part of the waste can be unscrewed to remove accumulated hair and debris. This helps prevent blockages and maintains efficient drainage.
- Check Seals: Occasionally inspect the seals for any signs of wear or damage. Replace if necessary to prevent leaks.
7. Troubleshooting
If you encounter issues with your basin waste, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaking around the waste flange | Improperly seated sealant or loose back nut. | Ensure sealant is correctly applied. Gently tighten the back nut. If leaks persist, remove, reapply sealant, and reinstall. |
| Slow drainage or blockage | Accumulation of hair and debris in the waste unit or trap. | Unscrew the top of the waste plug and remove any debris. Clean the trap if necessary. |
| Push mechanism not engaging | Debris interfering with the mechanism or internal component issue. | Remove the top part and clean the mechanism. If the issue persists, contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | W BASIN08 C |
| Main Construction Material | Brass |
| Connection Inlet | G1 1/4" |
| Style | Contemporary |
| Color | Chrome |
| Finish | Polished |
| Shape | Round |
| Item Weight | 210 g |
| Product Dimensions (L x W x H) | 6.8 x 6.8 x 7.8 cm |
| Measurement System | Metric |
| Batteries Required | No |
9. Warranty
This Bristan product is covered by a 5-year manufacturer's guarantee from the date of purchase. This warranty covers manufacturing defects under normal use and service. Please retain your proof of purchase for warranty claims. For full terms and conditions, please refer to the official Bristan website or contact customer support.
10. Support and Contact Information
For further assistance, technical support, or to inquire about spare parts, please contact Bristan directly:
- Website: www.bristan.com
- Email: enquire@bristan.com
- Telephone: 0330 026 6273
- Address: Bristan, Birch Coppice Business Park, Dordon, Tamworth, B78 1SG, United Kingdom
When contacting support, please have your product model number (W BASIN08 C) and date of purchase readily available.