Introduction
This manual provides instructions for the Amazon Basics 4K HDMI 5 Port Switch. This device allows you to connect up to five HDMI source devices to a single HDMI display, such as a TV or monitor, and switch between them easily. It supports 4K resolution at 30Hz and is HDCP compliant.
Safety Information
- Do not expose the device to moisture or extreme temperatures.
- Do not disassemble the device. Refer all servicing to qualified personnel.
- Use only the provided USB power cable.
- Ensure proper ventilation around the device.
Package Contents
- Amazon Basics 4K HDMI 5 Port Switch
- USB Power Cable (power only)
- Remote Control (CR2025 battery not included)
- User Manual
Image: The HDMI switch, its remote control, and the USB power cable included in the package.
Product Overview
The Amazon Basics 4K HDMI 5 Port Switch features five HDMI input ports and one HDMI output port. It includes a power input, an IR receiver for the remote control, and a manual selection button.
Image: A top-down view of the HDMI switch, highlighting the five HDMI input ports (INPUT1-INPUT5), one HDMI output port, and the DC 5V power input.
Front Panel
- POWER LED: Indicates power status.
- INPUT LEDs (1-5): Indicate the currently selected input port.
- SELECTION Button: Press to manually cycle through input sources.
- IR Receiver: For remote control signals.
Rear Panel
- HDMI INPUT (1-5): Connect your HDMI source devices (e.g., game console, Blu-ray player, computer).
- HDMI OUTPUT: Connect to your HDMI display (e.g., TV, monitor, projector).
- DC 5V: Power input port.
Setup
- Connect HDMI Source Devices: Plug up to five HDMI source devices (e.g., gaming consoles, media players, computers) into the HDMI INPUT ports (1-5) on the switch.
- Connect to Display: Connect an HDMI cable from the HDMI OUTPUT port on the switch to an HDMI input port on your TV, monitor, or projector.
- Connect Power: Plug the included USB power cable into the DC 5V port on the switch and connect the other end to a USB power source (e.g., a USB port on your TV or a USB wall adapter). The POWER LED on the switch will illuminate.
- Insert Remote Battery: Open the battery compartment of the remote control and insert a CR2025 battery (not included), ensuring correct polarity.
Image: The HDMI switch connected to a laptop via an HDMI cable, demonstrating a typical setup.
Operating Instructions
Switching Inputs
You can switch between connected HDMI sources using either the manual selection button on the device or the included remote control.
- Manual Switching: Press the "SELECTION" button on the front panel of the switch to cycle through the HDMI input ports (1-5). The corresponding INPUT LED will light up to indicate the active source.
- Remote Control Switching: Point the remote control towards the IR receiver on the front of the switch. Press the numbered buttons (1-5) on the remote to directly select the desired HDMI input port.
The switch does not feature automatic input sensing or switching. You must manually select the desired input.
Maintenance
- Clean the device with a soft, dry cloth. Do not use liquid cleaners or aerosols.
- Keep the device free from dust and debris to ensure proper ventilation.
- Store the device in a cool, dry place when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No signal on display. | Incorrect input selected. Loose HDMI cables. No power to the switch. Source device not active. | Ensure the correct input is selected on the switch and your display. Check all HDMI cable connections. Verify the USB power cable is connected and the POWER LED is on. Ensure the source device is powered on and outputting a signal. |
| Picture flickering or poor quality. | Faulty HDMI cable. Cable length too long. Resolution incompatibility. | Try a different HDMI cable. Ensure HDMI cables are within recommended length (e.g., under 10 ft for 4K). Verify your display and source device support the output resolution (e.g., 4K). |
| Remote control not working. | No battery or dead battery. Obstruction to IR receiver. Incorrect remote aim. | Insert a new CR2025 battery with correct polarity. Ensure a clear line of sight between the remote and the switch's IR receiver. Aim the remote directly at the IR receiver. |
Specifications
- Product Dimensions: 6.46 x 0.79 x 2.16 inches
- Item Weight: 11.4 ounces
- Model Number: AZSW5T1A-4K2K
- Connector Type: HDMI
- Input Ports: 5 x HDMI
- Output Ports: 1 x HDMI
- Resolution Support: Up to 4K @ 30Hz
- HDCP Compliance: HDCP 1.4b
- Power: DC 5V (via USB cable)
- Compatible Devices: Computer, PS4, Xbox, Blu-ray DVD player, STB, Projectors, HDTVs, Apple TV, monitors, etc.
Warranty and Support
For warranty information or technical support, please refer to the Amazon Basics official website or contact Amazon customer service. Keep your purchase receipt for warranty claims.
