Introduction
Thank you for choosing the Lindby Ragna LED Floor Lamp. This manual provides essential information for the safe and efficient use of your new lamp. Please read these instructions carefully before assembly and operation, and retain them for future reference.
Figure 1: The Lindby Ragna LED Floor Lamp, showcasing its modern design with an aluminum body and glass uplighter shade.
Important Safety Instructions
To reduce the risk of fire, electric shock, or injury, please observe the following:
- Ensure the power supply voltage matches the lamp's requirements before connecting.
- Do not operate the lamp with a damaged cord or plug.
- Avoid placing the lamp in unstable locations where it could tip over.
- Do not expose the lamp to water or excessive moisture. This product has an IP20 rating, meaning it is protected against solid objects larger than 12.5mm but has no protection against water.
- Do not attempt to modify or repair the lamp yourself. Contact qualified service personnel for repairs.
- Keep packaging materials out of reach of children to prevent suffocation hazards.
- The LED light source is integrated and not user-replaceable.
Package Contents
Verify that all components are present and undamaged upon opening the package. If any parts are missing or damaged, contact your retailer.
- Floor Lamp Base and Pole Assembly
- Glass Uplighter Shade
- Integrated LED Light Source
- Power Adapter with Cord
- Instruction Manual (this document)
Figure 2: Key components of the lamp, including the glass shade, LED module, and base plate, before assembly.
Setup and Assembly
Follow these steps to assemble your Lindby Ragna LED Floor Lamp:
- Unpack Components: Carefully remove all parts from the packaging. Place them on a soft, clean surface to prevent scratches.
- Assemble the Pole: The lamp pole may come in sections. Gently screw the pole sections together clockwise until secure. Ensure the power cord runs freely through the pole.
- Attach to Base: Securely attach the assembled pole to the heavy base by screwing it clockwise. Ensure it is stable and upright.
- Install the Shade: Carefully place the glass uplighter shade onto the top of the lamp pole. Ensure it sits correctly and is stable.
- Connect Power Adapter: Insert the small connector from the lamp's cord into the power adapter. Then, plug the power adapter into a standard wall outlet.
Figure 3: The power adapter correctly connected to the lamp's base for power supply.
Operating Instructions
The Lindby Ragna LED Floor Lamp is designed for simple operation.
- Power On/Off: Locate the rotary dimmer switch on the lamp pole. Turn the switch clockwise to turn the lamp on.
- Dimming Function: Continue turning the rotary switch clockwise to increase the light intensity. Turn it counter-clockwise to decrease the light intensity and eventually turn the lamp off.
Figure 4: Detail of the integrated rotary dimmer switch, used for controlling the lamp's power and brightness.
Figure 5: The Lindby Ragna LED Floor Lamp providing ambient uplighting in a room.
Maintenance and Care
Regular cleaning will help maintain the appearance and functionality of your lamp.
- Cleaning: Disconnect the lamp from the power outlet before cleaning. Use a soft, dry cloth to wipe the metal surfaces. For the glass shade, a slightly damp cloth can be used, followed by a dry cloth to prevent water spots.
- Do Not Use: Avoid abrasive cleaners, solvents, or polishing agents, as these can damage the finish.
- LED Light Source: The LED light source is integrated and designed for long-term use. It does not require replacement.
Troubleshooting
If you encounter issues with your lamp, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. |
|
|
| Light flickers or is unstable. |
|
|
| Lamp is unstable. |
|
|
If the problem persists after attempting these solutions, please contact customer support.
Technical Specifications
| Brand: | Lindby |
| Model Name: | Ragna |
| Manufacturer Reference: | 4251096519648 |
| ASIN: | B0799H1LLC |
| Light Source Type: | Integrated LED |
| Wattage: | 30 Watts |
| Material (Shade): | Glass |
| Material (Frame): | Aluminum |
| Color: | White (shade), Aluminum (frame) |
| Style: | Modern |
| Power Source: | Corded Electric |
| IP Rating: | IP20 |
| Weight: | 24.14 Pounds (approx. 10.95 kg) |
| Special Features: | Energy-Efficient, Dimmable (integrated) |
Figure 6: Energy efficiency label, indicating the lamp's energy class.
Warranty and Support
For warranty information, please refer to the terms and conditions provided at the point of purchase or contact your retailer. Lindby products are designed for quality and durability.
If you require technical assistance or have questions not covered in this manual, please contact Lindby customer support or your authorized dealer. Please have your model number (Ragna) and manufacturer reference (4251096519648) available when contacting support.
You can often find contact information on the manufacturer's official website or through your purchase platform.
