Boulder LED IP65 Washer 24x10W 4in1 Architecture Light User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your Boulder LED IP65 Washer 24x10W 4in1 Architecture Light. This high-performance lighting fixture is designed for outdoor architectural applications, offering robust construction and versatile color mixing capabilities. Please read this manual thoroughly before installation and use, and retain it for future reference.

2. Safety Information

• Always connect the fixture to a grounded circuit to avoid the risk of electrocution.
• Ensure the power supply voltage matches the specified range (AC90-260V 50-60Hz) to prevent damage.
• Do not operate the fixture if the power cord is damaged.
• Disconnect power before performing any maintenance or cleaning.
• Avoid direct eye exposure to the light source, as it can cause eye injury.
• Ensure proper ventilation around the fixture to prevent overheating.
• This fixture is IP65 rated for outdoor use, meaning it is protected against dust and low-pressure water jets. However, avoid submerging it in water.
• Installation should be performed by qualified personnel.

3. Product Overview

3.1 Key Features

• 24 x 10W 4-in-1 RGBW LEDs for 16.7 million color mixing.
• IP65 rated waterproof die-cast aluminum structure.
• Manually adjustable tilt angle for precise light positioning.
• High efficiency 25° optic lens.
• 50,000 hours LED lifespan.
• 0-100% smooth linear LED dimmer.
• LED rainbow effect and strobe effect (up to 25 flashes/second).
• Multiple control modes: DMX512, Master-Slave, Sound Activated, Auto Operation.
• LED display for easy configuration.
• Waterproof power and 3-pin DMX connectors (IN/OUT).
• Operating temperature range: -20°C to 45°C.

3.2 Components

The Boulder LED IP65 Washer consists of a robust housing, LED array, control panel, and waterproof connectors. Refer to the images below for visual identification of components.

Figure 1: Front view of the Boulder LED IP65 Washer, showcasing its LED array and various color outputs (blue, green, white, red) in separate panels.

Figure 2: Detailed front view of the Boulder LED IP65 Washer, highlighting the 24 individual LED lenses and the adjustable mounting bracket.

Figure 3: Rear view of the fixture, showing the LED display, control buttons (MENU, UP, DOWN, ENTER), DMX IN/OUT, and Power IN/OUT waterproof connectors.

Figure 4: Side view of the Boulder LED IP65 Washer, illustrating its robust aluminum housing and heat dissipation fins.

4. Setup and Installation

4.1 Mounting

The fixture can be mounted on a flat surface or suspended using appropriate clamps and safety cables. The integrated bracket allows for manual tilt angle adjustment. Ensure the mounting surface or structure can safely support the fixture's weight (7.5 kg net weight).

Figure 5: Example of a safety cable, recommended for securing the fixture when suspended to prevent accidental falls.

4.2 Electrical Connection

1. Connect the power cable to the POWER IN connector on the rear of the fixture.
2. If linking multiple fixtures, use the POWER OUT connector to daisy-chain power to the next fixture. Ensure the total power consumption does not exceed the circuit's capacity.
3. Plug the power cable into a suitable grounded power outlet (AC90-260V, 50-60Hz).

4.3 DMX Connection (Optional)

For DMX control, connect a DMX controller to the DMX IN connector using a 3-pin DMX cable. To daisy-chain multiple fixtures, connect the DMX OUT of the first fixture to the DMX IN of the next, and so on. A DMX terminator is recommended for the last fixture in a chain.

5. Operating Modes

The fixture can be operated in several modes, selectable via the LED display and control buttons (MENU, UP, DOWN, ENTER) on the rear panel.

5.1 LED Display Navigation

• MENU: Cycles through main menu options.
• UP/DOWN: Navigates through options or adjusts values within a selected menu.
• ENTER: Confirms selection or saves changes.

5.2 DMX512 Mode

This mode allows external control via a DMX controller. Set the DMX address for each fixture using the control panel. The fixture supports 4 or 9 DMX channels. Refer to Section 6 for DMX channel assignments.

5.3 Master-Slave Mode

In this mode, one fixture acts as the master, controlling other linked fixtures (slaves). Connect the DMX OUT of the master to the DMX IN of the first slave, and so on. Set the master fixture to an auto or sound-activated mode, and set slave fixtures to slave mode via the LED display.

5.4 Sound Activated Mode

The fixture's built-in microphone detects sound, triggering pre-programmed light sequences. Select this mode via the LED display.

5.5 Auto Operation Mode

The fixture runs through various pre-programmed internal light shows and color changes. Select this mode via the LED display.

6. DMX Channel Assignments

The Boulder LED IP65 Washer supports 4 or 9 DMX channels. The specific functions assigned to each channel depend on the selected DMX mode.

6.1 4-Channel Mode (Basic RGBW)

6.2 9-Channel Mode (Advanced Control)

Note: Specific DMX values for effects (strobe speed, color macros) may vary slightly. Refer to the fixture's LED display menu for precise settings if available.

7. Maintenance

7.1 Cleaning

• Regularly clean the lens and housing with a soft, lint-free cloth to maintain optimal light output and prevent dust buildup.
• Do not use abrasive cleaners or solvents.
• Ensure the fixture is powered off and cool before cleaning.

7.2 Storage

When not in use, store the fixture in a dry, dust-free environment, preferably in its original packaging or a protective case.

8. Troubleshooting

9. Specifications

Figure 6: Technical drawing showing the dimensions of the Boulder LED IP65 Washer in millimeters (D: 220mm, W: 340mm, H: 280mm).

Figure 7: Photometric beam angle data for the Boulder LED IP65 Washer, illustrating a 25-degree beam angle and lux values at various distances for R, G, B, W, and RGBW colors.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Manufacturer: Guangzhou Baide Lighting Co., LTD

Brand: Boulder