LAP Bronx Outdoor Up & Down Wall Light Stainless Steel Instruction Manual

1. Product Overview

The LAP Bronx Outdoor Up & Down Wall Light is a durable and stylish lighting solution designed for exterior use. Constructed from high-quality stainless steel, this fixture provides both upward and downward illumination, enhancing the aesthetic and safety of your outdoor spaces. It operates on a 240V power supply and requires two GU10 lamps.

Image: The LAP Bronx Outdoor Up & Down Wall Light, featuring a cylindrical stainless steel body mounted on a wall bracket. The bottom light source is illuminated, demonstrating its "down" lighting capability. The brushed stainless steel finish is visible.

2. Safety Information

Please read all instructions carefully before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• Electrical Safety: Installation must be carried out by a qualified electrician in accordance with all local wiring regulations and standards.
• Power Disconnection: Always ensure the main power supply is switched off at the consumer unit/fuse box before commencing any installation, maintenance, or bulb replacement.
• Outdoor Use: This product is designed for outdoor use and is water resistant. However, ensure all connections are properly sealed and protected from direct water ingress during installation.
• Bulb Type: Use only GU10 lamps as specified. Do not exceed the maximum wattage of 5W per lamp.
• Handling: Handle the light fixture and bulbs with care to prevent damage.

3. Setup and Installation

The LAP Bronx Wall Light comes with mounting hardware for installation. Professional installation is highly recommended to ensure safety and compliance with electrical codes.

1. Prepare the Installation Area: Choose a suitable outdoor location for the wall light. Ensure the surface is stable and can support the fixture's weight.
2. Disconnect Power: Before starting, turn off the electricity supply to the circuit at the main fuse box or circuit breaker.
3. Mount the Bracket: Secure the mounting bracket to the wall using the provided fixings. Ensure it is level and firmly attached.
4. Electrical Connection: Connect the light fixture's wiring to your mains electrical supply. Ensure correct polarity (Live, Neutral, Earth) and secure all connections within a suitable junction box or terminal block.
5. Attach the Fixture: Carefully attach the light fixture body to the mounted bracket, ensuring all wires are tucked away safely and not pinched.
6. Install GU10 Lamps: Insert two GU10 lamps into the lamp holders. Ensure they are securely twisted into place.
7. Restore Power: Once installation is complete and all components are securely in place, restore power at the main fuse box.
8. Test Operation: Test the light to ensure it functions correctly.

Note: The fixture dimensions are approximately 85 mm (Width) x 95 mm (Depth) x 158 mm (Height).

4. Operating Instructions

The LAP Bronx Outdoor Wall Light operates via your standard electrical wall switch. Simply toggle the switch to turn the light on or off.

5. Maintenance

Regular maintenance will help prolong the life and appearance of your light fixture.

• Cleaning: To clean the stainless steel surface, use a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
• Bulb Replacement:
  1. Ensure the power supply to the light is switched off at the main fuse box.
  2. Allow the existing bulb to cool down completely if it has been recently in use.
  3. Carefully remove the old GU10 lamp by twisting it counter-clockwise and pulling it out.
  4. Insert a new GU10 lamp, aligning the pins with the socket holes, and twist clockwise to secure.
  5. Restore power and test the new bulb.
• Recycling: For information on recycling light bulbs, please refer to local recycling guidelines or visit relevant environmental protection agency websites.
• Breakage: In case of bulb breakage, follow proper clean-up procedures to safely dispose of glass and bulb components.

6. Troubleshooting

If your LAP Bronx Wall Light is not functioning as expected, consider the following:

• Light Not Turning On:
  • Check if the main power supply to the light is switched on at the fuse box.
  • Ensure the wall switch controlling the light is in the "ON" position.
  • Verify that the GU10 lamps are correctly installed and not faulty. Try replacing them with known working bulbs.
  • Check for any loose wiring connections (only if you are a qualified electrician).
• Dim or Flickering Light:
  • Ensure the bulbs are fully seated in their sockets.
  • Check if the bulbs are compatible with the fixture and not exceeding the maximum wattage.
  • If the issue persists, consult a qualified electrician.

7. Specifications

8. Warranty Information

Specific warranty details for the LAP Bronx Outdoor Wall Light are typically provided at the point of purchase or can be obtained directly from the manufacturer, LAP. Please retain your proof of purchase for any warranty claims.

9. Support

For technical support, installation queries, or further assistance, please contact the retailer from whom you purchased this product. Alternatively, you may be able to find support information on the official LAP brand website.