FLEXISPOT E6+180 Standing Desk

1. Introduction

Thank you for choosing the FLEXISPOT E6+180 Electric Standing Desk. This manual provides essential information for the safe and efficient assembly, operation, and maintenance of your new desk. Please read this manual thoroughly before installation and use, and keep it for future reference.

The FLEXISPOT E6+180 is a robust and versatile electric standing desk designed to promote a healthier work environment by allowing seamless transitions between sitting and standing positions. It features a dual-motor, three-stage lifting system for smooth and stable height adjustments.

1.1 Important Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, or injury. This desk is intended for indoor use only.

1.2 Package Contents

Before assembly, please verify that all components are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact customer support immediately. Typical components include:

• Desk Frame (Legs, Crossbar)
• Desktop Surface
• Control Panel
• Power Adapter and Cable
• Mounting Hardware (Screws, Allen Keys)
• Cable Management Accessories

2. Safety Instructions

• Weight Capacity: Do not exceed the maximum load capacity of 125 kg (275 lbs). Overloading can cause damage to the desk and potential injury.
• Pinch Points: Keep hands, fingers, and other body parts clear of moving parts, especially during height adjustments, to avoid pinching or crushing injuries.
• Power Source: Connect the desk only to a properly grounded power outlet with the correct voltage as specified on the power adapter.
• Cable Management: Ensure all cables are properly routed and secured to prevent tripping hazards or damage during desk movement.
• Children and Pets: Keep children and pets away from the desk during operation. This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
• Liquid Spills: Avoid spilling liquids on the control panel or electrical components. In case of a spill, immediately unplug the desk and allow it to dry completely before reconnecting power.
• Uneven Surfaces: Do not operate the desk on uneven surfaces. Ensure the desk is stable and level before use.
• Modifications: Do not attempt to modify or disassemble the desk's electrical components. Repairs should only be performed by qualified service personnel.
• Environmental Conditions: Do not use the desk in excessively humid or dusty environments.

3. Setup and Assembly

Assembly typically requires two people. Ensure you have enough space and all tools provided or required (e.g., screwdriver).

1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface (e.g., carpet or blanket) to prevent scratches.
2. Assemble Legs to Crossbar: Attach the lifting columns (legs) to the central crossbar according to the diagrams in your specific assembly guide. Secure with the provided screws.
3. Attach Feet: Secure the desk feet to the bottom of the lifting columns using the appropriate screws.
4. Mount Desktop: Carefully place the desktop surface upside down on your soft surface. Position the assembled frame onto the desktop, aligning the pre-drilled holes. Secure the frame to the desktop using the provided screws.
5. Connect Control Box and Motors: Connect the motor cables from each leg to the control box. Connect the control panel cable to the control box. Ensure all connections are firm.
6. Install Control Panel: Mount the control panel to the underside of the desktop in a convenient location using the provided screws.
7. Cable Management: Use the included cable ties or clips to neatly route and secure all cables, preventing them from dangling or interfering with desk movement.
8. Connect Power: Plug the power adapter into the control box, then plug the power cable into a grounded electrical outlet.
9. Initial Calibration (if required): Some models may require an initial calibration. Refer to your specific model's quick start guide for instructions, typically involving pressing and holding the 'down' button until the desk reaches its lowest point and slightly retracts.

Note: No product images or videos were provided in the input. Therefore, visual aids for assembly steps cannot be embedded here. Please refer to the physical assembly guide included with your product for detailed diagrams.

4. Operating Instructions

4.1 Basic Height Adjustment

• Raise Desk: Press and hold the UP (▲) button to raise the desk to your desired standing height. Release the button to stop.
• Lower Desk: Press and hold the DOWN (▼) button to lower the desk to your desired sitting height. Release the button to stop.

4.2 Setting Memory Presets

Your desk features memory buttons (usually M1, M2, M3, M4) to save your preferred sitting and standing heights for quick adjustments.

1. Adjust the desk to your desired height using the UP/DOWN buttons.
2. Press the 'M' or 'SET' button (if available) once. The display may show 'S-' or 'MEM'.
3. Within 3 seconds, press the desired memory button (e.g., '1', '2', '3', or '4'). The display will show 'S-1', 'S-2', etc., or a confirmation beep, indicating the height is saved.
4. Repeat for other desired heights.

4.3 Using Memory Presets

To move the desk to a saved height, simply press the corresponding memory button (e.g., '1'). The desk will automatically move to the saved position. Press any button to stop the movement.

4.4 Advanced Features (if applicable)

• Child Lock: Some models have a child lock feature. To activate/deactivate, typically press and hold the 'M' button for 5 seconds until 'LOC' appears/disappears.
• Anti-Collision System: The desk is equipped with an anti-collision feature that stops and slightly reverses movement if it encounters an obstacle. Ensure the sensitivity is appropriate for your environment.

5. Maintenance

5.1 Cleaning

• Desktop Surface: Clean the desktop surface with a soft, damp cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive materials that could damage the finish.
• Frame and Legs: Wipe down the metal frame and legs with a dry or slightly damp cloth.
• Control Panel: Use a dry, soft cloth to clean the control panel. Do not spray cleaners directly onto the panel.
• Before Cleaning: Always unplug the desk from the power outlet before cleaning.

5.2 Periodic Checks

• Tighten Screws: Periodically check all screws and bolts to ensure they are tight. Loose fasteners can affect stability and performance.
• Cable Condition: Inspect power cables and motor cables for any signs of wear, cuts, or damage. Replace damaged cables immediately.
• Smooth Operation: Ensure the desk moves smoothly without unusual noises or jerky movements. If issues arise, refer to the troubleshooting section.

6. Troubleshooting

If you encounter any issues with your FLEXISPOT E6+180 desk, please consult the table below before contacting customer support.

7. Specifications

8. Warranty and Customer Support

8.1 Warranty Information

FLEXISPOT products are manufactured with high-quality materials and craftsmanship. This product is covered by a limited warranty against defects in materials and workmanship. The specific warranty period may vary by component (e.g., frame, motor, control panel). Please refer to the warranty card included with your purchase or visit the official FLEXISPOT website for detailed warranty terms and conditions.

The warranty typically covers manufacturing defects and does not cover damage caused by improper assembly, misuse, neglect, unauthorized modifications, or normal wear and tear.

8.2 Customer Support

If you have any questions, require assistance with assembly, or encounter issues not covered in the troubleshooting section, please do not hesitate to contact FLEXISPOT customer support. Have your model number and purchase information ready when contacting support.

For the most up-to-date contact information, please visit the official FLEXISPOT website:

www.flexispot.com